Infiniti M35/M45 Y50. Manual — part 916
FRONT FOG LAMP
LT-209
C
D
E
F
G
H
I
J
L
M
A
B
LT
4.
CHECK FOG LAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector (A) and
front fog lamp RH or LH harness connector (B).
4.
Check continuity between IPDM E/R harness connector (A) and
ground.
OK or NG
OK
>> Replace IPDM E/R. Refer to
PG-31, "Removal and Installation of IPDM E/R"
.
NG
>> Repair harness or connector.
Front Fog Lamps Do Not Turn OFF
NKS003RG
1.
CHECK FRONT FOG LAMP TURN OFF
Make sure that lighting switch is OFF. And make sure front fog lamp turns off when ignition switch is turned
OFF.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “HEAD LAMP” data monitor,
make sure “FR FOG SW” turns ON-OFF linked with operation of fog
lamp switch.
OK or NG
OK
>> Replace IPDM E/R. Refer to
.
NG
>> Check combination switch (lighting switch). Refer to
239, "Combination Switch Inspection"
.
Circuit
A
B
Continuity
Connector
Terminal
Connector
Terminal
RH
E8
36
E60
1
Yes
LH
37
E45
1
A
Ground
Continuity
Connector
Terminal
RH
E8
36
No
LH
37
SKIB4815E
When fog lamp switch is
OFF position
: FR FOG SW OFF
PKIB9378E
LT-210
FRONT FOG LAMP
3.
CHECK CAN COMMUNICATIONS BETWEEN BCM AND IPDM E/R
Select “BCM” on CONSULT-II, and perform self-diagnosis for “BCM”.
Display of self-diagnosis results
NO DTC>> Replace IPDM E/R. Refer to
CAN COMM CIRCUIT>> Refer to
Inspection Using CONSULT-II (Self-Diagnosis)"
Aiming Adjustment
NKS003RH
The fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing aiming
adjustment, make sure of the following.
●
Keep all tires inflated to correct pressure.
●
Place vehicle on level ground.
Adjust aiming in the vertical direction by turning the adjusting screw.
1.
Set the distance between the screen and the center of fog lamp
lens as shown.
2.
Turn front fog lamps ON.
3.
Adjust front fog lamps using adjusting screw so that the top edge
of the high intensity zone is in the figure.
When performing adjustment, if necessary, cover the headlamps
and opposite fog lamp.
PKIA7627E
SKIB4160E
SKIB0897E
FRONT FOG LAMP
LT-211
C
D
E
F
G
H
I
J
L
M
A
B
LT
Bulb Replacement
NKS003RI
1.
Turn lighting switch OFF.
2.
Remove fender protector (front). Refer to
3.
Turn bulb (1) counterclockwise and unlock it.
4.
Disconnect connector (2), and remove bulb (1).
CAUTION:
●
Never touch the glass of bulb directly by hand. Keep grease
and other oily matters away from it. Never touch bulb by
hand while it is lit or right after being turned off.
●
Never leave bulb out of fog lamp reflector for a long time
because dust, moisture smoke, etc. may affect the perfor-
mance of fog lamp. When replacing bulb, be sure to replace
it with new one.
Removal and Installation
NKS003RJ
REMOVAL
1.
Remove front bumper grille (1). Refer to
Installation of Front Bumper Grille"
.
2.
Remove screws (2) and remove front fog lamp (3) from vehicle.
: N·m (kg-m, in-lb)
INSTALLATION
Installation is the reverse order of removal.
Front fog lamp
: 12V - 55W (H11)
SKIB4161E
SKIB4162E
Front fog lamp mounting bolt
: 5.5 N·m (0.56 kg-m, 49 in-lb)
LT-212
TURN SIGNAL AND HAZARD WARNING LAMPS
TURN SIGNAL AND HAZARD WARNING LAMPS
PFP:26120
Component Parts and Harness Connector Location
NKS003RK
System Description
NKS003RL
TURN SIGNAL OPERATION
With the ignition switch is in the ON or START position, power is supplied
●
through 15A fuse [No. 1, located in fuse block (J/B)]
●
to BCM (body control module) terminal 38,
●
through 10A fuse [No. 14, located in fuse block (J/B)]
●
to combination meter terminal 12,
●
through 10A fuse [No. 12, located in fuse block (J/B)]
●
to unified meter and A/C amp. terminal 53.
Ground is supplied
●
to BCM terminal 52
●
to combination meter terminals 9, 10 and 11
●
to unified meter and A/C amp. terminals 55 and 71
●
through grounds M16 and M70.
PKIC0620E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст