Infiniti M35/M45 Y50. Manual — part 1128
TROUBLE DIAGNOSIS
TF-19
C
E
F
G
H
I
J
K
L
M
A
B
TF
TDWT0023E
TF-20
TROUBLE DIAGNOSIS
Trouble Diagnosis Chart for Symptoms
NDS000DK
If AWD warning lamp turns ON, perform self-diagnosis. Refer to
TF-22, "SELF-DIAG RESULT MODE"
NOTE:
Light tight-corner braking symptom may occur depending on driving conditions. This is not malfunction.
AWD Control Unit Input/Output Signal Reference Values
NDS000DL
AWD CONTROL UNIT INSPECTION TABLE
Specifications with CONSULT-II
Symptom
Condition
Check item
Reference page
AWD warning lamp does not turn ON when
the ignition switch is turned to ON.
(AWD warning lamp check)
Ignition switch: ON
CAN communication line
Unified meter and A/C amp.
Unified meter control unit
AWD warning lamp does not turn OFF sev-
eral seconds after engine started.
Engine running
CAN communication line
Power supply and ground for AWD con-
trol unit
Unified meter and A/C amp.
Unified meter control unit
AWD solenoid
AWD actuator relay (integrated in AWD
control unit)
Wheel sensor
Heavy tight-corner braking symptom occurs
when the vehicle is driven and the steering
wheel is turned fully to either side after the
engine is started. (See NOTE.)
●
While driving
●
Steering wheel is
turned fully to either
sides
CAN communication line
Accelerator pedal position signal
AWD solenoid
Mechanical malfunction of electric con-
trolled coupling (clutch sticking etc.)
Vehicle does not enter AWD mode even
though AWD warning lamp turned to OFF.
While driving
CAN communication line
AWD solenoid
Mechanical malfunction of electric con-
trolled coupling (Mechanical engage-
ment of clutch is not possible.)
While driving, AWD warning lamp flashes
rapidly. (When flashing in approx. 1 minute
and then turning OFF.)
Rapid flashing: 2 times/second
While driving
Protection function is activated due to
heavy load to electric controlled cou-
pling. (AWD system is not malfunction-
ing. Also, optional distribution of torque
sometimes becomes rigid before lamp
flashes rapidly, but it is not malfunction.)
While driving, AWD warning lamp flashes
slowly. (When continuing to flash until turn-
ing ignition switch OFF)
Slow flashing: 1 time/2 seconds
●
While driving
●
Vehicle speed: 20 km/h
(12 MPH) or more
Tire size is different between front and
rear of vehicle.
Monitor item [Unit]
Content
Condition
Display value
FR RH SENSOR [km/h] or [mph]
Wheel speed (Front wheel
right)
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under
standard condition.
Approximately equal to
the indication on speed-
ometer (Inside of
±
10%)
FR LH SENSOR [km/h] or [mph]
Wheel speed (Front wheel
left)
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under
standard condition.
Approximately equal to
the indication on speed-
ometer (Inside of
±
10%)
TROUBLE DIAGNOSIS
TF-21
C
E
F
G
H
I
J
K
L
M
A
B
TF
*
1
: The values are changed by throttle opening and engine speed.
*
2
: Mode switch is not equipped, but displayed.
CONSULT-II Function (ALL MODE AWD/4WD)
NDS000DM
FUNCTION
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
RR RH SENSOR [km/h] or [mph]
Wheel speed (Rear wheel
right)
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under
standard condition.
Approximately equal to
the indication on speed-
ometer (Inside of
±
10%)
RR LH SENSOR [km/h] or [mph]
Wheel speed (Rear wheel
left)
Vehicle stopped
0.00 km/h (0.00 mph)
Vehicle running
CAUTION:
Check air pressure of tire under
standard condition.
Approximately equal to
the indication on speed-
ometer (Inside of
±
10%)
BATTERY VOLT [V]
Power supply voltage for
AWD control unit
Ignition switch: ON
Battery voltage
THRTL POS SEN [%]
Throttle opening condition
When depressing accelerator pedal
(Value rises gradually in response to
throttle position.)
0 - 100%
ETS SOLENOID [A]
Monitored value of current at
AWD solenoid
Engine running
●
At idle speed
Approx. 0.000A
Engine running
●
When depressing accelerator
pedal
Approx. 0.000 - 0.500A*
1
STOP LAMP SW [ON/OFF]
Condition of brake pedal
operation
Brake pedal: Depressed
ON
Brake pedal: Released
OFF
ENG SPEED SIG [RUN/STOP]
Condition of engine running
Engine stopped
(Engine speed: Less than 400 rpm)
STOP
Engine running
(Engine speed: 400 rpm or more)
RUN
ETS ACTUATOR [ON/OFF]
Operating condition of AWD
actuator relay (integrated in
AWD control unit)
Engine stopped (Ignition
switch: ON)
OFF
Engine running
ON
4WD WARN LAMP [ON/OFF]
AWD warning lamp condition
AWD warning lamp: ON
ON
AWD warning lamp: OFF
OFF
4WD MODE SW*
2
[AUTO]
Input condition from mode
switch
Always
AUTO
4WD MODE MON [AUTO]
Control status of AWD
Engine running
AUTO
DIS-TIRE MONI [mm]
Improper size tire installed
condition
Vehicle running with normal size tire
installed
0-4 mm
Vehicle running with improper size
tire installed (Front/rear tire size dif-
ference, wear condition)
4-8 mm, 8- mm
P BRAKE SW [ON/OFF]
Condition of parking brake
Parking brake operated
ON
Parking brake not operated
OFF
Monitor item [Unit]
Content
Condition
Display value
Diagnostic test mode
Function
Reference
page
Self-diagnostic results
●
Self-diagnostic results can be read and erased quickly.
Data monitor
●
Input/Output data in the AWD control unit can be read.
TF-22
TROUBLE DIAGNOSIS
CONSULT-II SETTING PROCEDURE
Refer to
GI-38, "CONSULT-II Start Procedure"
SELF-DIAG RESULT MODE
Operation Procedure
1.
Perform “CONSULT-II Start Procedure”. Refer to
GI-38, "CONSULT-II Start Procedure"
2.
Start engine and drive at 30 km/h (19 MPH) or more for approx. 1 minute.
3.
Stop vehicle. With engine at idle, touch “SELF-DIAG RESULTS”.
Display shows malfunction experienced since the last erasing
operation.
NOTE:
●
The details for “TIME” are as follow:
–
“0”: Error currently detected with AWD control unit.
–
Except for “0”: Error detected in the past and memorized
with AWD control unit.
Detects frequency of driving after DTC occurs (frequency
of turning ignition switch “ON/OFF”).
Display Item List
CAUTION:
●
If “CAN COMM CIRCUIT [U1000]” is displayed with other DTCs, first perform the trouble diagnosis for CAN communica-
tion line.
●
Make sure that ABS warning lamp turns OFF by driving for a minute at vehicle speed of 30 km/h (19 MPH) or more after
turning ignition switch “OFF” if AWD warning lamp turns ON with system malfunction of “ABS SYSTEM [C1203]”. AWD
warning lamp may not turn OFF if it is normal unless ignition switch turns OFF at once and engine restarts after that.
How to Erase Self-Diagnostic Results
1.
Perform applicably inspection of malfunctioning item and then repair or replace.
2.
Start engine and drive at 30 km/h (19 MPH) or more for approx. 1 minute.
3.
Make sure that ABS warning lamp turns OFF.
CAN diagnostic support monitor
●
The results of transmit/receive diagnosis of CAN communication can be read.
Active test
●
Diagnostic Test Mode in which CONSULT-II drives some actuators apart from
the AWD control unit and also shifts some parameters in a specified range.
ECU part number
●
AWD control unit part number can be read.
Diagnostic test mode
Function
Reference
page
SDIA2217E
Items (CONSULT-II screen
terms)
Diagnostic item is detected when...
Check item
CONTROLLER FAILURE
[C1201]
Malfunction has occurred inside AWD control unit.
ABS SYSTEM
[C1203]
Malfunction related to wheel sensor has been detected by ABS actu-
ator and electric unit (control unit).
4WD SOLENOID
[C1204]
Malfunction related to AWD solenoid has been detected.
4WD ACTUATOR RLY
[C1205]
Malfunction has been detected from AWD actuator relay integrated
with AWD control unit, or malfunction related to AWD solenoid has
been detected.
ENGINE SIGNAL 1
[C1210]
Malfunction has been detected from ECM.
TF-32, "Engine Control Sig-
nal"
CAN COMM CIRCUIT
[U1000]
When AWD control unit is not transmitting or receiving CAN commu-
nication signal for 2 seconds or more.
TF-32, "CAN Communica-
tion Line"
NO DTC IS DETECTED.
FURTHER TESTING MAY BE
REQUIRED.
No NG item has been detected.
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст