Infiniti M35/M45 Y50. Manual — part 428
DTC P0075, P0081 IVT CONTROL SOLENOID VALVE
EC-185
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0075, P0081 IVT CONTROL SOLENOID VALVE
PFP:23796
Component Description
NBS004UG
Intake valve timing control solenoid valve is activated by ON/OFF
pulse duty (ratio) signals from the ECM.
The intake valve timing control solenoid valve changes the oil
amount and direction of flow through intake valve timing control unit
or stops oil flow.
The longer pulse width advances valve angle.
The shorter pulse width retards valve angle.
When ON and OFF pulse widths become equal, the solenoid valve
stops oil pressure flow to fix the intake valve angle at the control
position.
CONSULT-II Reference Value in Data Monitor Mode
NBS004UH
Specification data are reference values.
On Board Diagnosis Logic
NBS004UI
DTC Confirmation Procedure
NBS004UJ
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and let it idle for 5 seconds.
4.
If 1st trip DTC is detected, go to
EC-190, "Diagnostic Procedure"
.
WITH GST
Following the procedure “WITH CONSULT-II” above.
PBIB1842E
MONITOR ITEM
CONDITION
SPECIFICATION
INT/V SOL (B1)
INT/V SOL (B2)
●
Engine: After warming up
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Idle
0% - 2%
When revving engine up to 2,000 rpm
quickly
Approx. 25% - 50%
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0075
0075
(Bank 1)
Intake valve timing control
solenoid valve circuit
An improper voltage is sent to the ECM
through intake valve timing control solenoid
valve.
●
Harness or connectors
(Intake valve timing control solenoid valve
circuit is open or shorted.)
●
Intake valve timing control solenoid valve
P0081
0081
(Bank 2)
SEF058Y
EC-186
[VQ35DE]
DTC P0075, P0081 IVT CONTROL SOLENOID VALVE
Wiring Diagram
NBS004UK
BANK 1
TBWT0971E
DTC P0075, P0081 IVT CONTROL SOLENOID VALVE
EC-187
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
11
W/R
Intake valve timing control
solenoid valve (bank 1)
[Engine is running]
●
Warm-up condition
●
Idle speed
BATTERY VOLTAGE
(11 - 14V)
[Engine is running]
●
Warm-up condition
●
When revving engine up to 2,000rpm
quickly
7 - 12V
111
SB
ECM relay
(Self shut-off)
[Engine is running]
[Ignition switch: OFF]
●
For a few seconds after turning ignition
switch OFF
0 - 1.5V
[Ignition switch: OFF]
●
More than a few seconds after turning igni-
tion switch OFF
BATTERY VOLTAGE
(11 - 14V)
119
120
R
R
Power supply for ECM
[Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14V)
PBIB1790E
EC-188
[VQ35DE]
DTC P0075, P0081 IVT CONTROL SOLENOID VALVE
BANK 2
TBWT0972E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст