Infiniti M35/M45 Y50. Manual — part 363
UNIFIED METER AND A/C AMP
DI-35
C
D
E
F
G
H
I
J
L
M
A
B
DI
DTC [U1000] CAN Communication Circuit
NKS003UK
Symptom: Displays “CAN COMM CIRC [U1000]” as a self-diagnosis results of unified meter and A/C amp.
1.
CHECK CAN COMMUNICATION
1.
Select “SELF-DIAG RESULTS” mode for “METER A/C AMP” with CONSULT-II.
2.
Print out CONSULT-II screen.
>> Go to “LAN system”. Refer to
LAN-44, "CAN Diagnostic Support Monitor"
.
DTC [B2202] Meter Communication Circuit
NKS003UL
Symptom: Displays “METER COMM CIRC [B2202]” as a self-diagnosis results of unified meter and A/C amp.
1.
CHECK CONNECTOR
Check combination meter, unified meter and A/C amp. and terminals (combination meter side, unified meter
and A/C amp. side, and harness side) for looseness or bent.
OK or NG
OK
>> GO TO 2.
NG
>> Repair terminal or connector.
2.
CHECK CONTINUITY COMMUNICATION CIRCUIT (TX: UNIFIED METER AND A/C AMP.)
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and unified meter and A/C amp. connector.
3.
Check continuity between combination meter harness connector
(A) and unified meter and A/C amp. harness connector (B).
4.
Check continuity between combination meter harness connector
(A) and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
A
B
Continuity
Connector
Terminal
Connector
Terminal
M52
15
M64
7
Yes
A
Ground
Continuity
Connector
Terminal
M52
15
No
PKIB7647E
DI-36
UNIFIED METER AND A/C AMP
3.
CHECK CONTINUITY COMMUNICATION CIRCUIT (RX: UNIFIED METER AND A/C AMP.)
1.
Check continuity between combination meter harness connector
(A) and unified meter and A/C amp. harness connector (B).
2.
Check continuity between combination meter harness connector
(A) and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair harness or connector.
4.
CHECK COMBINATION METER OUTPUT VOLTAGE (TX: UNIFIED METER AND A/C AMP.)
1.
Connect combination meter connector.
2.
Turn ignition switch ON.
3.
Check voltage between combination meter harness connector
and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Replace combination meter.
A
B
Continuity
Connector
Terminal
Connector
Terminal
M52
16
M64
27
Yes
A
Ground
Continuity
Connector
Terminal
M52
16 No
PKIB7648E
Terminals
Voltage (Approx.)
(+)
(–)
Combination meter
connector
Terminal
M52
15
Ground
5 V
PKIB7649E
UNIFIED METER AND A/C AMP
DI-37
C
D
E
F
G
H
I
J
L
M
A
B
DI
5.
CHECK COMMUNICATION SIGNAL (TX: UNIFIED METER AND A/C AMP.)
1.
Turn ignition switch OFF.
2.
Connect unified meter and A/C amp. connector.
3.
Turn ignition switch ON.
4.
Check voltage signal between combination meter harness con-
nector and ground.
OK or NG
OK
>> GO TO 6.
NG
>> Replace unified meter and A/C amp.
6.
CHECK UNIFIED METER AND A/C AMP OUTPUT VOLTAGE (RX: UNIFIED METER AND A/C AMP.)
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Turn ignition switch ON.
4.
Check voltage between unified meter and A/C amp. harness
connector and ground.
OK or NG
OK
>> GO TO 7.
NG
>> Replace unified meter and A/C amp.
Terminals
Voltage (Approx.)
(+)
(–)
Combination meter
connector
Terminal
M52
15
Ground
PKIB7650E
SKIA3362E
Terminals
Voltage (Approx.)
(+)
(–)
Unified meter and A/C
amp. connector
Terminal
M64
27 Ground
5
V
PKIB7651E
DI-38
UNIFIED METER AND A/C AMP
7.
CHECK COMMUNICATION SIGNAL (RX: UNIFIED METER AND A/C AMP.)
1.
Turn ignition switch OFF.
2.
Connect combination meter connector.
3.
Turn ignition switch ON.
4.
Check voltage signal between unified meter and A/C amp. har-
ness connector and ground.
OK or NG
OK
>> Replace unified meter and A/C amp.
NG
>> Replace combination meter.
DTC [B2205] Vehicle Speed Circuit
NKS003UM
Symptom: Displays “VEHICLE SPEED CIRC [B2205]” as a self-diagnosis results of unified meter and A/C
amp.
Preform self-diagnosis of ABS actuator and electric unit (control unit), and repair or replace malfunctioning
parts. Refer to
BRC-23, "CONSULT-II Functions (ABS)"
.
Removal and Installation of Unified Meter and A/C Amp.
NKS003UN
REMOVAL
1.
Remove the audio unit. Refer to
(Without
mobile entertainment system) or
mobile entertainment system).
2.
Remove the screws (A) 2.
3.
Remove the screws (B) 4 and remove the bracket (1).
4.
Remove unified meter and A/C amp. (2).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Unified meter and A/C amp. screws (A) are different from other screws. Never confuse them when
installing.
Terminals
Voltage (Approx.)
(+)
(–)
Unified meter
and A/C amp.
connector
Terminal
M64
27
Ground
PKIB7652E
SKIA3361E
SKIB4053E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст