Infiniti M35/M45 Y50. Manual — part 691
DTC P1550 BATTERY CURRENT SENSOR
EC-1237
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P1550 BATTERY CURRENT SENSOR
PFP:294G0
Component Description
NBS005LF
The power generation voltage variable control enables fuel con-
sumption to be decreased by reducing the engine load which is
caused by the power generation of the generator. The battery cur-
rent sensor (1) is installed to the battery cable at the negative termi-
nal. The sensor measures the charging/discharging current of the
battery. Based on the sensor signal, ECM judges whether or not the
power generation voltage variable control is performed. When per-
forming the power generation voltage variable control, ECM calcu-
lates the target power generation voltage based on the sensor
signal. And ECM sends the calculated value as the power genera-
tion command value to IPDM E/R. For the details of the power gen-
eration voltage variable control, refer to SC section.
CAUTION:
Do not connect the electrical component or the ground wire directly to the battery terminal. The con-
nection causes the malfunction of the power generation voltage variable control, and then the battery
discharge may occur.
CONSULT-II Reference Value in Data Monitor Mode
NBS005LG
Specification data are reference values.
*: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
SC-5, "SPECIFIC GRAVITY CHECK"
On Board Diagnosis Logic
NBS005LH
The MIL will not light up for this diagnosis.
NOTE:
If DTC P1550 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to
EC-1193, "DTC P0643 SENSOR POWER SUPPLY"
.
PBIB2685E
MONITOR ITEM
CONDITION
SPECIFICATION
BAT CUR SEN
●
Engine speed: Idle
●
Battery: Fully charged*
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Approx. 2,600 - 3,500mV
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1550
1550
Battery current sensor circuit
range/performance
The output voltage of the battery current
sensor remains within the specified
range while engine is running.
●
Harness or connectors
(The sensor circuit is open or shorted.)
●
Battery current sensor
EC-1238
[VK45DE]
DTC P1550 BATTERY CURRENT SENSOR
DTC Confirmation Procedure
NBS005LI
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V at idle.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Start engine and wait at least 10 seconds.
4.
If 1st trip DTC is detected, go to
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
SEF058Y
DTC P1550 BATTERY CURRENT SENSOR
EC-1239
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
NBS005LJ
TBWT1064E
EC-1240
[VK45DE]
DTC P1550 BATTERY CURRENT SENSOR
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
*: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to
SC-5, "SPECIFIC GRAVITY CHECK"
Diagnostic Procedure
NBS005LK
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten ground screws on the body.
Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
49
B/Y
Sensor power supply
(Battery current sensor)
[Ignition switch: ON]
Approximately 5V
67
B/W
Sensor ground
(Battery current sensor)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 0V
71
L/R
Battery current sensor
[Engine is running]
●
Battery: Fully charged*
●
Idle speed
Approximately 2.6 - 3.5V
1.
Body ground M70
2.
Body ground M16
PBIB2782E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст