Infiniti M35/M45 Y50. Manual — part 290
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-229
C
D
E
F
G
H
J
K
L
M
A
B
BL
Terminals and Reference Value of BCM
NIS001ZZ
Terminals and Reference Value of IPDM E/R
NIS00200
Termi-
nal
Wire
color
Item
Signal
Input/
Output
Condition
Voltage [V]
(Approx.)
11
V
Power supply (ACC)
Input
Ignition switch (ACC or ON
position)
Battery voltage
12
P
Front door switch
passenger side signal
Input
ON (Open)
→
OFF
(Closed)
0
→
Battery voltage
13
O/L
Rear door switch RH signal
Input
ON (Open)
→
OFF
(Closed)
0
→
Battery voltage
22
G
Power window serial link
Input/
Output
Ignition switch ON or power
window timer operating
23
W/V
Security indicator lamp
Output
Goes off
→
Illuminates
Battery voltage
→
0
37
LG
Key switch signal
Input
Key inserted in key slot
→
key removed from key slot
Battery voltage
→
0
39
L
CAN-H
Input/
Output
—
—
40
P
CAN-L
Input/
Output
—
—
42
P
Power source (fuse)
Input
—
Battery voltage
52
B
Ground
—
—
0
55
W
Battery power supply (fusible link)
Input
—
Battery voltage
56
W
Trunk lid key cylinder switch
Input
Neutral
→
Unlock
Battery voltage
→
0
57
SB
Trunk room lamp switch signal
Input
ON (Open)
→
OFF
(Closed)
0
→
Battery voltage
62
V
Front door switch
driver side signal
Input
ON (Open)
→
OFF
(Closed)
0
→
Battery voltage
63
R/G
Rear door switch LH signal
Input
ON (Open)
→
OFF
(Closed)
0
→
Battery voltage
PIIA2344J
Terminal Wire
color
Item
Signal
Input/Output
Condition
Voltage [V]
(Approx.)
38
B
Ground (power)
—
—
0
48
G/B
Horn relay control signal
Output
Panic alarm is operating
0
Other than above
Battery voltage
49
L
CAN-H
Input/Output
—
—
50
P
CAN-L
Input/Output
—
—
51
B
Ground (signal)
—
—
0
60
LG/B
Hood switch signal
Input
ON (Open)
→
OFF (closed)
0
→
Battery voltage
BL-230
VEHICLE SECURITY (THEFT WARNING) SYSTEM
CONSULT-II Function (BCM)
NIS00201
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CAUTION:
CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunction might be detected in
self-diagnosis depending on control units with carry out CAN communication.
BASIC OPERATION
Refer to
GI-38, "CONSULT-II Start Procedure"
CONSULT-II APPLICATION ITEM
Work Support
Data Monitor
BCM diagnosis
position
Inspection items and diagnosis mode
Description
THEFT ALM
DATA MONITOR
Displays the input data to BCM in real time basis.
ACTIVE TEST
Gives a drive signal to a load to check the operation.
WORK SUPPORT
Changes setting of each function.
Test Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and
erase the record of vehicle security alarm. The trigger data can be erased by touching “CLEAR”
on CONSULT-II screen.
Monitored Item
Description
IGN ON SW
Indicates [ON/OFF] condition of ignition switch.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
I-KEY DR UNLK
Indicates [ON/OFF] condition of unlock signal from driver side door request switch.
I-KEY AS UNLK
Indicates [ON/OFF] condition of unlock signal from passenger side door request switch.
I-KEY LOCK
Indicates [ON/OFF] condition of lock signal from Intelligent Key.
I-KEY UNLOCK
Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
I-KEY TRNK/HAT
Indicates [ON/OFF] condition of trunk opener signal from Intelligent Key.
TRUNK OPNR SW
This is displayed even when it is not equipped.
TRUNK CYL SW
This is displayed even when it is not equipped.
TRUNK OPN MNTR
Indicates [ON/OFF] condition of trunk room lamp switch.
HOOD SW
Indicates [ON/OFF] condition of hood switch.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW
This is displayed even when it is not equipped.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from front door key cylinder switch.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from front door key cylinder switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch LH and RH.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch LH and RH.
VEHICLE SECURITY (THEFT WARNING) SYSTEM
BL-231
C
D
E
F
G
H
J
K
L
M
A
B
BL
Active Test
Trouble Diagnosis Work Flow
NIS00202
1.
CHECK IN
Listen to customer complaint.
>> GO TO 2.
2.
CHECK FUNCTION
Do “Power door lock system” and “Intelligent Key system” work properly?
YES
>> GO TO 3.
NO
>> Preform diagnosis and repair. Refer to
BL-43, "INTELLIGENT KEY SYSTEM"
3.
PERFORM DIAGNOSTIC PROCEDURE
Perform diagnostic procedure according to the symptom chart. Refer to
BL-233, "Trouble Diagnosis Symptom
.
>> GO TO 4.
4.
FINAL CHECK
Confirm that the malfunction is completely fixed by operating the system.
OK
>> INSPECTION END
NG
>> GO TO 3.
Preliminary Check
NIS00203
1.
INSPECTION START
Turn ignition switch "OFF" and pull out Intelligent Key from key slot.
NOTE:
Before starting operation check, open front windows.
>> GO TO 2.
2.
CHECK SECURITY INDICATOR LAMP
1.
Lock doors using Intelligent Key or mechanical key.
2.
Make sure security indicator lamp illuminate for 30 seconds.
Security indicator lamp should illuminate.
OK
>> GO TO 3.
NG
>> Perform diagnosis and repair. Refer to
BL-234, "Diagnostic Procedure 1"
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. The lamp will be turned on when “ON”
on CONSULT-II screen is touched.
VEHICLE SECURITY HORN
This test is able to check vehicle security horn operation. The horns will be activated for 0.5 sec-
onds after “ON” on CONSULT-II screen is touched.
HEADLAMP(HI)
This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5
seconds after “ON” on CONSULT-II screen is touched.
FLASHER
This test is able to check vehicle security hazard lamp operation. The hazard lamps will be acti-
vated after “ON” on CONSULT-II screen is touched.
BL-232
VEHICLE SECURITY (THEFT WARNING) SYSTEM
3.
CHECK ALARM FUNCTION
1.
After 30 seconds, security indicator lamp will start blink.
2.
Open any door or hood before unlocking with Intelligent Key or mechanical key, or open trunk lid without
Intelligent Key or mechanical key.
Do alarm function properly.
OK
>> GO TO 4.
NG
>> Check the following.
●
The vehicle security system does not phase in alarm mode. Refer to
.
●
Alarm (horn, headlamp and hazard lamp) do not operate. Refer to
4.
CHECK ALARM CANCEL OPERATION
Unlock any door or open trunk lid using Intelligent Key or mechanical key.
Alarm (horn, headlamp and hazard lamp) should stop.
OK
>> INSPECTION END.
NG
>> Perform diagnosis and repair. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст