Infiniti M35/M45 Y50. Manual — part 379
LANE DEPARTURE WARNING SYSTEM
DI-99
C
D
E
F
G
H
I
J
L
M
A
B
DI
LDW Indicator Lamp Circuit Inspection
NKS003VX
1.
CHECK OPERATION OF LDW INDICATOR LAMP
Check LDW indicator operation “INDICATOR LAMP DRIVE” in
“ACTIVE TEST” mode with CONSULT-II.
OK or NG
OK
>> LDW indicator is OK. Return to
NG
>> GO TO 2.
2.
CHECK LDW INDICATOR LAMP SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect LDW camera unit connector and combination meter
connector.
3.
Check continuity between LDW camera unit harness connector
(A) and combination meter harness connector (B).
4.
Check continuity between LDW camera unit harness connector
(A) and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK LDW INDICATOR LAMP
1.
Connect combination meter connector.
2.
Turn ignition switch ON.
3.
Apply ground to combination meter terminal.
4.
Check condition of the LDW indicator lamp.
OK or NG
OK
>> Replace LDW camera unit.
NG
>> Replace combination meter.
“INDICATOR LAMP DRIVE”
Touch “ON”
: LDW indicator lamp illuminates.
Touch “OFF”
: LDW indicator lamp OFF.
PKIB4692E
A
B
Continuity
Connector
Terminal
Connector
Terminal
M182
8
M52
8
Yes
A
Ground
Continuity
Connector
Terminal
M182
8 No
PKIB7671E
Combination meter
connector
Terminal
Ground
Condition
M52
8
LDW indicator lamp should
illuminate.
PKIB7672E
DI-100
LANE DEPARTURE WARNING SYSTEM
Turn Signal Input Inspection
NKS003VY
1.
CHECK TURN SIGNAL INPUT
Check turn signal input “TURN SIGNAL” in “DATA MONITOR” mode
with CONSULT-II.
OK or NG
OK
>> Turn signal input is OK. Return to
NG
>> Check turn signal and hazard warning lamps system,
and repair or replace corresponding parts. Refer to
LT-221, "How to Perform Trouble Diagnoses"
.
Electrical Component Inspection
NKS003VZ
LDW SWITCH
Check continuity between terminals 6 and 7.
Removal and Installation for LDW Camera Unit
NKS003W0
REMOVAL
1.
2.
Disconnect LDW camera unit connector (1).
3.
Remove the bolts (A), and remove LDW camera unit (2).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
●
Remove the camera lens cap for replacement.
●
Never give an impact to the LDW camera unit.
●
Adjust the camera aiming every time the LDW camera unit is removed or installed. Refer to
“TURN SIGNAL”
When lighting switch is in TURN RH position
: RH
When lighting switch is in TURN LH position
: LH
When hazard switch is turned ON
: RH/LH
SKIB3125E
Terminal
Condition
Continuity
6
7
When LDW switch is pushed.
Yes
When LDW switch is released.
No
PKIC0258E
PKIB7673E
LANE DEPARTURE WARNING SYSTEM
DI-101
C
D
E
F
G
H
I
J
L
M
A
B
DI
Removal and Installation for LDW Chime
NKS003W1
REMOVAL
1.
Remove instrument side panel (LH). Refer to
2.
Remove the bolt (A).
3.
Remove LDW chime (1).
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation for LDW Switch
NKS003W2
Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
PKIB7674E
DI-102
COMPASS
COMPASS
PFP:24835
Precautions for Compass
NKS004F2
NOTE:
●
Do not install the ski rack, antenna, etc. which is attach to the vehicle with a magnet base. It affects the
operation of the compass.
●
When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not
spray glass cleaner directly on the mirror as it may cause the liquid cleaner to enter the mirror housing.
System Description
NKS004F3
●
This electronic compass is able to display 8 primary directions: N, NE, E, SE, S, SW, W, NW.
●
The compass switch (1) is used to operate the compass.
Switch Operation
●
All standard compasses determine direction relative to Magnetic North; however, this electronic compass
is designed to display direction relative to True North.
●
The difference between Magnetic North and True North varies from place to place across the surface of
the earth.
●
This electronic compass must be “told” approximately where it is on the earth’s surface so that the Mag-
netic North reading can be properly converted into a True North display.
●
To tell the electronic compass where it’s at, the earth is separated into numbered “Zone Variances”. The
Zone Variance number in which the compass is to function must be entered into this electronic compass.
●
Each zone is magnetically about 4.2
°
wide. Typically, anything under 22.5
°
total zone change is not
noticed on the electronic compass display. However, over 22.5
°
, a reading may be off by one or more pri-
mary directions.
●
On long trips, a vehicle may leave its original zone and enter one or more new zones. Generally, you do
not need to reset the compass zone if you travel between 3 or 4 zones, such as business travel or vaca-
tion. The typical driver will not notice any difference on the display within 3 or 4 zones. However, if the
vehicle is “permanently” moved to a new location, it is recommended that the compass zone be reset.
(1)
: Compass switch
(2)
: Compass display
SKIB8868E
Press
Compass is turned ON/OFF
Press and hold
(for 3 – 9 sec.)
Compass display turns to zone variation change
mode
Press and hold
(for more than 9 sec.)
Compass display turns to calibration mode
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст