Infiniti M35/M45 Y50. Manual — part 624
DTC P0132, P0152 A/F SENSOR 1
EC-969
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
2
SB
A/F sensor 1 heater
(bank 1)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 5V
16
W/L
A/F sensor 1 (bank 1)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 3.1V
35
GR/L
Approximately 2.6V
56
LG/B
Approximately 2.3V
75
Y
Approximately 2.3V
PBIB1584E
EC-970
[VK45DE]
DTC P0132, P0152 A/F SENSOR 1
BANK 2
TBWT1047E
DTC P0132, P0152 A/F SENSOR 1
EC-971
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Diagnostic Procedure
NBS005E9
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten ground screws on the body.
Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
24
SB
A/F sensor 1 heater
(bank 2)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 5V
57
BR/W
A/F sensor 1 (bank 2)
[Engine is running]
●
Warm-up condition
●
Idle speed
Approximately 2.6V
58
G/O
Approximately 2.3V
76
G/W
Approximately 3.1V
77
GR
Approximately 2.3V
PBIB1584E
1.
Body ground M70
2.
Body ground M16
PBIB2782E
EC-972
[VK45DE]
DTC P0132, P0152 A/F SENSOR 1
2.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
Disconnect air fuel ratio (A/F) sensor 1 harness connector.
2.
Turn ignition switch ON.
3.
Check voltage between A/F sensor 1 terminal 3 and ground with
CONSULT-II or tester.
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E12, F3
●
IPDM E/R harness connector E7
●
15A fuse
●
Harness for open or short between A/F sensor 1 and fuse
>> Repair or replace harness or connectors.
: Vehicle front
1.
A/F sensor 1 (bank 2) harness con-
nector
2.
A/F sensor 1 (bank 1) harness con-
nector
Voltage: Battery voltage
PBIB2715E
PBIB1683E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст