Infiniti FX35 / FX45. Manual — part 587
DTC P2122, P2123 APP SENSOR
EC-1109
< SERVICE INFORMATION >
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
OK
>> GO TO 8.
NG
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E211, M41
• Harness for open or short between ECM and accelerator pedal position sensor
>> Repair open circuit or short to ground or short to power in harness or connectors.
8.
CHECK APP SENSOR
EC-1128, "Component Inspection"
.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 9.
9.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly.
2.
EC-662, "Accelerator Pedal Released Position Learning"
.
3.
EC-663, "Throttle Valve Closed Position Learning"
4.
EC-663, "Idle Air Volume Learning"
.
>> INSPECTION END
10.
CHECK INTERMITTENT INCIDENT
>> INSPECTION END
Component Inspection
INFOID:0000000001327006
ACCELERATOR PEDAL POSITION SENSOR
1.
Reconnect all harness connectors disconnected.
2.
Turn ignition switch ON.
3.
Check voltage between ECM terminals 106 (APP sensor 1 sig-
nal), 98 (APP sensor 2 signal) and ground under the following
conditions.
4.
If NG, replace accelerator pedal assembly and go to next step.
5.
EC-662, "Accelerator Pedal Released Position Learning"
.
6.
EC-663, "Throttle Valve Closed Position Learning"
7.
EC-663, "Idle Air Volume Learning"
.
Removal and Installation
INFOID:0000000001327007
ACCELERATOR PEDAL
.
Terminal
Accelerator pedal
Voltage
106
(Accelerator pedal position
sensor 1)
Fully released
0.5 - 1.0V
Fully depressed
3.9 - 4.7V
98
(Accelerator pedal position
sensor 2)
Fully released
0.15 - 0.60V
Fully depressed
1.95 - 2.40V
MBIB0023E
EC-1110
< SERVICE INFORMATION >
[VK45DE]
DTC P2127, P2128 APP SENSOR
DTC P2127, P2128 APP SENSOR
Component Description
INFOID:0000000001327008
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelera-
tor position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometers which transform the accelerator pedal
position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of
the accelerator pedal and feed the voltage signals to the ECM. The
ECM judges the current opening angle of the accelerator pedal from
these signals and controls the throttle control motor based on these
signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine oper-
ation such as fuel cut.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000001327009
Specification data are reference values.
*: Accelerator pedal position sensor 2 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage.
On Board Diagnosis Logic
INFOID:0000000001327010
These self-diagnoses have the one trip detection logic.
FAIL-SAFE MODE
When the malfunction is detected, ECM enters fail-safe mode and the MIL lights up.
DTC Confirmation Procedure
INFOID:0000000001327011
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
PBIB1741E
MONITOR ITEM
CONDITION
SPECIFICATION
ACCEL SEN 1
• Ignition switch: ON
(Engine stopped)
Accelerator pedal: Fully released
0.5 - 1.0V
Accelerator pedal: Fully depressed
4.0 - 4.8V
ACCEL SEN 2*
• Ignition switch: ON
(Engine stopped)
Accelerator pedal: Fully released
0.3 - 1.2V
Accelerator pedal: Fully depressed
3.9 - 4.8V
CLSD THL POS
• Ignition switch: ON
(Engine stopped)
Accelerator pedal: Fully released
ON
Accelerator pedal: Slightly depressed
OFF
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2127
2127
Accelerator pedal posi-
tion sensor 2 circuit low
input
An excessively low voltage from the APP sen-
sor 2 is sent to ECM.
• Harness or connectors
(APP sensor 2 circuit is open or shorted.)
(TP sensor circuit is shorted.)
• Accelerator pedal position sensor
(APP sensor 2)
• Electric throttle control actuator
(TP sensor 1 and 2)
P2128
2128
Accelerator pedal posi-
tion sensor 2 circuit high
input
An excessively high voltage from the APP sen-
sor 2 is sent to ECM.
Engine operating condition in fail-safe mode
The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10
degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition.
So, the acceleration will be poor.
DTC P2127, P2128 APP SENSOR
EC-1111
< SERVICE INFORMATION >
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V at idle.
1.
Start engine and let it idle for 1 second.
2.
Check DTC.
3.
If DTC is detected, go to
EC-1112, "Diagnosis Procedure"
Wiring Diagram
INFOID:0000000001327012
TBWM1355E
EC-1112
< SERVICE INFORMATION >
[VK45DE]
DTC P2127, P2128 APP SENSOR
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnosis Procedure
INFOID:0000000001327013
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body.
Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
2.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-I
TER-
MI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
47
L
Sensor power supply (Throt-
tle position sensor)
[Ignition switch: ON]
Approximately 5V
82
B/W
Sensor ground
(APP sensor 1 / ICC steering
switch / ASCD steering
switch)
[Engine is running]
• Warm-up condition
• Idle speed
Approximately 0V
83
G/OR
Sensor ground
(APP sensor 2)
[Engine is running]
• Warm-up condition
• Idle speed
Approximately 0V
90
L/B
Sensor power supply
(APP sensor 1)
[Ignition switch: ON]
Approximately 5V
91
G
Sensor power supply
(APP sensor 2)
[Ignition switch: ON]
Approximately 5V
98
Y/R
Accelerator pedal position
sensor 2
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released
0.15 - 0.60V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed
1.95 - 2.40V
106
OR
Accelerator pedal position
sensor 1
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released
0.5 - 1.0V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed
3.9 - 4.7V
PBIB2195E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст