Infiniti FX35 / FX45. Manual — part 507
DTC P0122, P0123 TP SENSOR
EC-789
< SERVICE INFORMATION >
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
5.
Check voltage between ECM terminals 50 (TP sensor 1 signal),
69 (TP sensor 2 signal) and ground under the following condi-
tions.
6.
If NG, replace electric throttle control actuator and go to the next
step.
7.
EC-663, "Throttle Valve Closed Position Learning"
8.
EC-663, "Idle Air Volume Learning"
.
Removal and Installation
INFOID:0000000001326624
ELECTRIC THROTTLE CONTROL ACTUATOR
.
Terminal
Accelerator pedal
Voltage
50
(Throttle position sensor 1)
Fully released
More than 0.36V
Fully depressed
Less than 4.75V
69
(Throttle position sensor 2)
Fully released
Less than 4.75V
Fully depressed
More than 0.36V
PBIB1530E
EC-790
< SERVICE INFORMATION >
[VK45DE]
DTC P0125 ECT SENSOR
DTC P0125 ECT SENSOR
Component Description
INFOID:0000000001326625
NOTE:
If DTC P0125 is displayed with P0117 or P0118, first perform the trouble diagnosis for DTC P0117 or
P0118. Refer to
.
The engine coolant temperature sensor is used to detect the engine
coolant temperature. The sensor modifies a voltage signal from the
ECM. The modified signal returns to the ECM as the engine coolant
temperature input. The sensor uses a thermistor which is sensitive to
the change in temperature. The electrical resistance of the ther-
mistor decreases as temperature increases.
<Reference data>
*: These data are reference values and are measured between ECM terminal 73
(Engine coolant temperature sensor) and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
On Board Diagnosis Logic
INFOID:0000000001326626
DTC Confirmation Procedure
INFOID:0000000001326627
CAUTION:
Be careful not to overheat engine.
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-III
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-III.
3.
Check that “COOLAN TEMP/S” is above 10
°
C (50
°
F).
If it is above 10
°
C (50
°
F), the test result will be OK.
If it is below 10
°
C (50
°
F), go to following step.
SEF594K
Engine coolant
temperature
°
C (
°
F)
Voltage*
V
Resistance
k
Ω
–10 (14)
4.4
7.0 - 11.4
20 (68)
3.5
2.1 - 2.9
50 (122)
2.2
0.68 - 1.00
90 (194)
0.9
0.236 - 0.260
SEF012P
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0125
0125
Insufficient engine cool-
ant temperature for
closed loop fuel control
• Voltage sent to ECM from the sensor is not
practical, even when some time has passed
after starting the engine.
• Engine coolant temperature is insufficient for
closed loop fuel control.
• Harness or connectors
(High resistance in the circuit)
• Engine coolant temperature sensor
• Thermostat
DTC P0125 ECT SENSOR
EC-791
< SERVICE INFORMATION >
[VK45DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4.
Start engine and run it for 65 minutes at idle speed.
If “COOLAN TEMP/S” increases to more than 10
°
C (50
°
F) within 65 minutes, stop engine because
the test result will be OK.
5.
Check 1st trip DTC.
6.
If 1st trip DTC is detected, go to
WITH GST
Follow the procedure “WITH CONSULT-III” above.
Diagnosis Procedure
INFOID:0000000001326628
1.
CHECK GROUND CONNECTIONS
1.
Turn ignition switch OFF.
2.
Loosen and retighten three ground screws on the body.
Refer to
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace ground connections.
2.
CHECK ENGINE COOLANT TEMPERATURE SENSOR
EC-791, "Component Inspection"
OK or NG
OK
>> GO TO 3.
NG
>> Replace engine coolant temperature sensor.
3.
CHECK THERMOSTAT OPERATION
When the engine is cold [lower than 70
°
C (158
°
F)] condition, grasp lower radiator hose and confirm the engine
coolant does not flow.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace thermostat. Refer to
4.
CHECK INTERMITTENT INCIDENT
>> INSPECTION END
Component Inspection
INFOID:0000000001326629
ENGINE COOLANT TEMPERATURE SENSOR
PBIB2195E
EC-792
< SERVICE INFORMATION >
[VK45DE]
DTC P0125 ECT SENSOR
1.
Check resistance between engine coolant temperature sensor
terminals 1 and 2 as shown in the figure.
<Reference data>
2.
If NG, replace engine coolant temperature sensor.
Removal and Installation
INFOID:0000000001326630
ENGINE COOLANT TEMPERATURE SENSOR
PBIB2005E
Temperature
°
C (
°
F)
Resistance
k
Ω
20 (68)
2.1 - 2.9
50 (122)
0.68 - 1.00
90 (194)
0.236 - 0.260
SEF012P
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст