Infiniti FX35 / FX45. Manual — part 945
SRS-40
< SERVICE INFORMATION >
SIDE CURTAIN AIR BAG MODULE
SIDE CURTAIN AIR BAG MODULE
Removal and Installation
INFOID:0000000001327767
WARNING:
• Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3
minutes.
• Always work from the side of the side curtain air bag module.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove headlining. Refer to
EI-43, "Component Parts Location"
.
2.
Disconnect side curtain air bag connector.
NOTE:
• For installing / removing side curtain air bag module connec-
tor, insert thin screwdriver wrapped in tape into notch, lift lock
and remove connector.
• Install connector with lock raised, and push lock into connec-
tor.
• After installing the connector, make sure that the lock is
pushed securely into it.
3.
Remove side curtain air bag module fixing bolts, and then remove the side curtain air bag module.
CAUTION:
• Always place the side curtain air bag module with the warning
label facing upward.
• Do not disassemble side curtain air bag module.
• Do not insert any foreign objects (screwdriver, etc.) into air
bag module connector.
1. Side curtain air bag Inflator
2. Side curtain air bag
3. Bolt
4. Assist grip bracket
5. Bolt (There is no torque control)
PHIA0656E
PHIA0953J
PHIA0317E
SIDE CURTAIN AIR BAG MODULE
SRS-41
< SERVICE INFORMATION >
C
D
E
F
G
I
J
K
L
M
A
B
SRS
N
O
P
• Replace side curtain air bag module if it has been dropped or
sustained an impact.
• Do not expose the air bag module to temperatures exceeding
90
°
C (194
°
F).
• Do not allow oil, grease or water to come in contact with the
side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Be careful not to damage the air bag harness.
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function
and delete the memory by CONSULT-III.
• In case that malfunction is still detected after the avove operation, perform self-diagnosis to repair
malfunctions. Refer to Refer to
SBF814E
SRS-42
< SERVICE INFORMATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Removal and Installation
INFOID:0000000001327768
WARNING:
• Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3
minutes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove front grille. Refer to
EI-22, "Component Parts Location"
2.
Remove crash zone sensor connector.
3.
Remove crash zone sensor fixing nuts.
CAUTION:
• Replace crash zone sensor if it has been dropped or sustained an impact.
• Do not disassemble crash zone sensor.
• Do not use old fixing nuts after removal; replace with new nuts.
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Be careful not to damage the crash zone sensor harness.
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function
and delete the memory by CONSULT
−
III.
• In case that malfunction is still detected after the above operation, perform self-diagnosis to repair
.
PHIA0316E
SIDE AIR BAG (SATELLITE) SENSOR
SRS-43
< SERVICE INFORMATION >
C
D
E
F
G
I
J
K
L
M
A
B
SRS
N
O
P
SIDE AIR BAG (SATELLITE) SENSOR
Removal and Installation
INFOID:0000000001327769
WARNING:
• Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3
minutes.
• Do not use air tools or electric tools for servicing.
REMOVAL
1.
Remove seat belt pre-tensioner. Refer to
SB-3, "Removal and Installation of Front Seat Belt"
.
2.
Remove side air bag (Satellite) sensor fixing nuts.
3.
Remove the side air bag (Satellite) sensor connector.
CAUTION:
• Do not use old nuts; replace with new ones.
• Check side air bag (Satellite) sensor to ensure it is free of deformities, dents, cracks or rust. If it
shows any visible signs of damage, replace it with new one.
• Do not disassemble side air bag (Satellite) sensor.
• Replace side air bag (Satellite) sensor if it has been dropped or sustained an impact.
• Replace the satellite sensor of deployed SRS front side air bag and deployed SRS side curtain air
bag.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Be careful not to damage the satellite sensor harness.
• After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
• In case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function
and delete the memory by CONSULT
−
III.
• In case that malfunction is still detected after the above operation, perform self-diagnosis to repair
malfunctions. Refer to
PHIA0314E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст