Infiniti Q45 (FY33). Manual — part 69
SAT353B
e.
Install control valve assembly on transmission case.
f.
Install connector tube brackets and tighten bolts
q
A
and
q
B
.
I
Check that terminal assembly harness does not catch.
Bolt
mm (in)
q
A
33 (1.30)
q
B
45 (1.77)
SAT221B
g.
Install O-ring on oil strainer.
I
Apply petroleum jelly to O-ring.
h.
Install oil strainer on control valve.
SAT009B
i.
Securely fasten terminal harness with clips.
SAT010B
j.
Install torque converter clutch solenoid valve and A/T fluid tem-
perature sensor connectors.
GI
MA
EM
LC
EC
FE
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
ASSEMBLY
Assembly (2) (Cont’d)
AT-273
SAT011B
11. Install oil pan.
a.
Attach a magnet to oil pan.
SAT610I
b.
Install new oil pan gasket on transmission case.
c.
Install oil pan and bracket on transmission case.
I
Always replace oil pan bolts as they are self-sealing bolts.
I
Before installing bolts, remove traces of sealant and oil
from mating surface and thread holes.
I
Tighten four bolts in a criss-cross pattern to prevent dis-
location of gasket.
d.
Tighten drain plug.
SAT062J
12. Install PNP switch.
a.
Check that manual shaft is in “1” position.
b.
Temporarily install PNP switch on manual shaft.
c.
Move manual shaft to “N”.
SAT063J
d.
Tighten bolts while inserting 4.0 mm (0.157 in) dia. pin verti-
cally into locating holes in PNP switch and manual shaft.
SAT015BA
13. Install torque converter.
a.
Pour ATF into torque converter.
I
Approximately 2 liters (2-1/8 US qt, 1-3/4 Imp qt) of fluid
are required for a new torque converter.
I
When reusing old torque converter, add the same amount
of fluid as was drained.
ASSEMBLY
Assembly (2) (Cont’d)
AT-274
SAT016B
b.
Install torque converter while aligning notches and oil pump.
SAT017B
c.
Measure distance A to check that torque converter is in proper
position.
Distance “A”:
22 mm (0.87 in) or more
GI
MA
EM
LC
EC
FE
PD
FA
RA
BR
ST
RS
BT
HA
EL
IDX
ASSEMBLY
Assembly (2) (Cont’d)
AT-275
General Specifications
Engine
VH41DE
Automatic transmission model
RE4R03A
Transmission model code number
52X14
Stall torque ratio
1.84 : 1
Transmission gear ratio
1st
2.569
2nd
1.479
Top
1.000
OD
0.694
Reverse
2.275
Recommended fluid
Nissan Matic “D” (Continental
U.S. and Alaska) or Genuine
Nissan Automatic Transmission
Fluid (Canada)*
Fluid capacity
(US qt, Imp qt)
10.5 (11-1/8, 9-1/4)
*: Refer to MA section (“Fluids and Lubricants”, “RECOMMENDED
FLUIDS AND LUBRICANTS”).
Specifications and Adjustment
SHIFT SCHEDULE
Vehicle speed when shifting gears
Throttle position
Vehicle speed km/h (MPH)
D
1
,
D
2
D
2
,
D
3
D
3
,
D
4
D
4
,
D
3
D
3
,
D
2
D
2
,
D
1
1
2
,
1
1
Full throttle
66 - 70
(41 - 43)
120 - 128
(75 - 80)
183 - 193
(114 - 120)
177 - 187
(110 - 116)
114 - 122
(71 - 76)
43 - 47
(27 - 29)
53 - 57
(33 - 35)
Half throttle
44 - 48
(27 - 30)
80 - 86
(50 - 53)
119 - 127
(74 - 79)
81 - 89
(50 - 55)
35 - 39
(22 - 24)
7 - 11
(4 - 7)
53 - 57
(33 - 35)
Vehicle speed when performing and
releasing lock-up
Throttle
position
Selector lever
position
[Shift position]
Vehicle speed km/h (MPH)
Lock-up
“ON”
Lock-up
“OFF”
Full throttle
D
[D
4
]
184 - 192
(114 - 119)
178 - 186
(111 - 116)
D
[D
3
]
91 - 99
(57 - 62)
86 - 94
(53 - 58)
Half throttle
D
[D
4
]
134 - 142
(83 - 88)
120 - 128
(75 - 80)
D
[D
3
]
91 - 99
(57 - 62)
81 - 89
(50 - 55)
STALL REVOLUTION
Stall revolution rpm
2,300 - 2,500
LINE PRESSURE
Engine speed
rpm
Line pressure kPa (kg/cm
2
, psi)
D, 2 and 1 positions
R position
Idle
431 - 470
(4.4 - 4.8, 63 - 68)
598 - 637
(6.1 - 6.5, 87 - 92)
Stall
1,039 - 1,117
(10.6 - 11.4, 151 - 162)
1,450 - 1,539
(14.8 - 15.7, 210 - 223)
SERVICE DATA AND SPECIFICATIONS (SDS)
AT-276
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст