Infiniti M45 (Y34). Manual — part 41
TROUBLE DIAGNOSIS
AT-49
D
E
F
G
H
I
J
K
L
M
A
B
AT
4
4-3
Part 2
❏
Vehicle Cannot Be Started From D1.
❏
A/T Does Not Shift: D1
→
D2.
❏
A/T Does Not Shift: D2
→
D3.
❏
A/T Does Not Shift: D3
→
D4.
Part 3
❏
Cannot Be Changed To Manual Mode.
❏
A/T Does Not Shift: 5th gear
→
4th gear.
❏
A/T Does Not Shift: 4th gear
→
3rd gear.
❏
A/T Does Not Shift: 3rd gear
→
❏
A/T Does Not Shift: 2nd gear
→
❏
Vehicle Does Not Decelerate By Engine Brake.
❏
Perform self-diagnostics. Enter checks for detected items.
❏
Vehicle speed sensor·A/T.
❏
Vehicle speed sensor·MTR.
❏
❏
TCC solenoid valve.
❏
Line pressure solenoid valve.
❏
Input clutch solenoid valve.
❏
Front brake solenoid valve.
❏
Low coast brake solenoid valve.
.
❏
High and low reverse clutch solenoid valve.
.
❏
PNP switch.
❏
A/T fluid temperature sensors 1, 2.
❏
Turbine revolution sensors 1, 2.
.
❏
A/T interlock.
.
❏
❏
.
❏
Accelerator pedal position signal.
.
❏
Engine sped signal.
❏
CAN communication.
❏
TCM power supply.
.
❏
Battery
❏
Other
5
❏
Inspect each system for items found to be NG in the self-diagnostics and repair or replace the malfunction
parts.
6
❏
Perform all road tests and enter the checks again for the required items.
7
❏
For any remaining NG items, execute the “diagnostics procedure” and repair or replace the malfunction parts.
See the chart for diagnostics by symptoms. (This chart also contains other symptoms and inspection proce-
dures.)
8
❏
Erase the results of the self-diagnostics from the TCM.
,
AT-50
TROUBLE DIAGNOSIS
A/T Electrical Parts Location
ACS004HO
SCIA1486E
TROUBLE DIAGNOSIS
AT-51
D
E
F
G
H
I
J
K
L
M
A
B
AT
Circuit Diagram
ACS004HP
TCWA0108E
AT-52
TROUBLE DIAGNOSIS
Inspections Before Trouble Diagnosis
ACS004HQ
A/T FLUID CHECK
Fluid Leakage and Fluid Level Check
●
Inspect for fluid leakage and check the fluid level. Refer to
.
Fluid Condition Check
Inspect the fluid condition.
STALL TEST
Stall Test Procedure
1.
Inspect the amount of engine oil. Replenish the engine oil if necessary.
2.
Drive for about 10 minutes to warm up the vehicle so that the A/
T fluid temperature is 50 to 80
°
C (122 to 176
°
F). Inspect the
amount of A/T fluid. Replenish if necessary.
3.
Securely engage the parking brake so that the tires do not turn.
4.
Engine start, apply foot brake, and place selector lever in “D”
position.
5.
While holding down the foot brake, gradually press down the
accelerator pedal.
6.
Quickly read off the stall speed, then quickly remove your foot
from the accelerator pedal.
CAUTION:
Do not hold down the accelerator pedal for more than 5 sec-
onds during this test.
7.
Move the selector lever to “N” position.
8.
Cool down the A/T fluid.
Fluid status
Conceivable Cause
Required Operation
Varnished (viscous
varnish state)
Clutch, brake
scorched
Replace the A/T fluid and check the
A/T main unit and the vehicle for
malfunctions (wire harnesses,
cooler pipes, etc.)
Milky white or
cloudy
Water in the fluid
Replace the A/T fluid and check for
places where water is getting in.
Large amount of
metal powder mixed
in
Unusual wear of
sliding parts within
A/T
Replace the A/T fluid and check for
improper operation of the A/T.
SAT638A
SAT647B
SCIA1224E
SAT514G
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст