Infiniti M45 (Y34). Manual — part 421
DTC P0455 EVAP CONTROL SYSTEM
EC-373
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK FUEL TANK VACUUM RELIEF VALVE
Refer to
EC-695, "FUEL TANK VACUUM RELIEF VALVE (BUILT INTO FUEL FULLER CAP)"
.
OK or NG
OK
>> GO TO 5.
NG
>> Replace fuel filler cap with a genuine one.
5.
CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks, improper connection or
disconnection.
Refer to
EC-693, "EVAPORATIVE EMISSION LINE DRAWING"
.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or reconnect the hose.
6.
CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 7.
7.
CHECK EVAP CANISTER VENT CONTROL VALVE, O-RING AND CIRCUIT
Refer to
EC-558, "DTC Confirmation Procedure"
OK or NG
OK
>> GO TO 8.
NG
>> Repair or replace EVAP canister vent control valve and O-ring or harness/connector.
8.
INSTALL THE PRESSURE PUMP
To locate the EVAP leak, install EVAP service port adapter and pres-
sure pump to EVAP service port securely.
NOTE:
Improper installation of the EVAP service port adapter to the
EVAP service port may cause leaking.
With CONSULT-II>>GO TO 9.
Without CONSULT-II>>GO TO 10.
PBIB1114E
SEF916U
EC-374
DTC P0455 EVAP CONTROL SYSTEM
9.
CHECK FOR EVAP LEAK
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “EVAP SYSTEM CLOSE” of “WORK SUPPORT” mode
with CONSULT-II.
3.
Touch “START” and apply pressure into the EVAP line until the
pressure indicator reaches the middle of the bar graph.
CAUTION:
●
Never use compressed air or a high pressure pump.
●
Do not exceed 4.12 kPa (0.042 kg/cm
2
, 0.6 psi) of pres-
sure in the system.
4.
Using EVAP leak detector, locate the EVAP leak. For the leak
detector, refer to the instruction manual for more details.
Refer to
EC-693, "EVAPORATIVE EMISSION LINE DRAWING"
.
OK or NG
OK
>> GO TO 11.
NG
>> Repair or replace.
PEF917U
SEF200U
DTC P0455 EVAP CONTROL SYSTEM
EC-375
C
D
E
F
G
H
I
J
K
L
M
A
EC
10.
CHECK FOR EVAP LEAK
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Apply 12 volts DC to EVAP canister vent control valve. The valve will close. (Continue to apply 12 volts
until the end of test.)
3.
Apply 12 volts DC to vacuum cut valve bypass valve. The valve will open. (Continue to apply 12 volts until
the end of test.)
4.
Pressurize the EVAP line using pressure pump with 1.3 to 2.7 kPa (10 to 20 mmHg, 0.39 to 0.79 inHg),
then remove pump and EVAP service port adapter.
CAUTION:
●
Never use compressed air or a high pressure pump.
●
Do not exceed 4.12 kPa (0.042 kg/cm
2
, 0.6 psi) of pressure in the system.
5.
Using EVAP leak detector, locate the EVAP leak. For the leak
detector, refer to the instruction manual for more details. Refer
to
EC-693, "EVAPORATIVE EMISSION LINE DRAWING"
OK or NG
OK
>> GO TO 12.
NG
>> Repair or replace.
11.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT-II
1.
Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
2.
Start engine.
3.
Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode.
4.
Touch “Qu” on CONSULT-II screen to increase “PURG VOL
CONT/V” opening to 100%.
5.
Check vacuum hose for vacuum when revving engine up to
2,000 rpm.
OK or NG
OK
>> GO TO 14.
NG
>> GO TO 13.
PBIB0026E
SEF200U
PBIB0828E
EC-376
DTC P0455 EVAP CONTROL SYSTEM
12.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
Without CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Stop engine.
3.
Disconnect vacuum hose to EVAP canister purge volume control solenoid valve at EVAP service port.
4.
Start engine and let it idle for at least 80 seconds.
5.
Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
OK or NG
OK
>> GO TO 15.
NG
>> GO TO 13.
13.
CHECK VACUUM HOSE
Check vacuum hoses for clogging or disconnection. Refer to
OK or NG
OK (With CONSULT-II)>>GO TO 14.
OK (Without CONSULT-II)>>GO TO 15.
NG
>> Repair or reconnect the hose.
14.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
With CONSULT-II
1.
Start engine.
2.
Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode with
CONSULT-II. Check that engine speed varies according to the
valve opening.
OK or NG
OK
>> GO TO 16.
NG
>> GO TO 15.
15.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Refer to
EC-550, "Component Inspection"
OK or NG
OK
>> GO TO 16.
NG
>> Replace EVAP canister purge volume control solenoid valve.
16.
CHECK FUEL TANK TEMPERATURE SENSOR
Refer to
EC-291, "Component Inspection"
OK or NG
OK
>> GO TO 17.
NG
>> Replace fuel level sensor unit.
17.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Refer to
EC-369, "Component Inspection"
OK or NG
OK
>> GO TO 18.
NG
>> Replace EVAP control system pressure sensor.
PBIB0828E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст