Infiniti M45 (Y34). Manual — part 744
CHARGING SYSTEM
SC-27
C
D
E
F
G
H
I
J
L
M
A
B
SC
Removal and Installation
AKS002EI
REMOVAL
1.
Remove battery. Refer to
SC-8, "Removal and Installation"
.
2.
Remove air intake duct. Refer to
EM-16, "AIR CLEANER AND AIR DUCT"
in “ENGINE MECHANICAL
(EM)” section.
3.
Remove alternator, water pump and A/C compressor belt. Refer to
EM-13, "Removal and Installation"
“ENGINE MECHANICAL (EM)” section.
4.
Remove power steering hose clamp mounting bolt.
5.
Remove alternator stay mounting bolts and alternator stay.
6.
Remove radiator reservoir tank and radiator reservoir tank
bracket. Refer to
in “ENGINE COOLING
SYSTEM (CO)” section.
7.
Remove battery ground harness mounting bolt.
8.
Remove engine room harness clip.
1.
Alternator stay
2.
Alternator
3.
Alternator ground harness
4.
Alternator B terminal
5.
Battery ground harness
6.
Alternator bracket
PKIA1806E
PKIA1807E
PKIA1808E
SC-28
CHARGING SYSTEM
9.
Remove alternator mounting bolt.
10. Remove alternator bracket mounting bolts and alternator
bracket.
11. Remove B terminal nut.
12. Disconnect alternator connector.
13. Remove alternator ground harness mounting bolt.
14. Remove power steering oil reservoir tank mounting bolts, then
slide power steering oil reservoir tank.
15. Remove alternator assembly from vehicle upper side.
INSTALLATION
Install in the reverse order of removal, taking care of the following point.
●
Install alternator, and check tension of belt. Refer to
MECHANICAL (EM)” section.
CAUTION:
Be sure to tighten B terminal mounting nut carefully.
PKIA1809E
PKIA1810E
CHARGING SYSTEM
SC-29
C
D
E
F
G
H
I
J
L
M
A
B
SC
Disassembly and Assembly
AKS002EJ
1.
Pulley
2.
Front cover
3.
Front bearing
4.
Retainer
5.
Rotor
6.
Rear bearing
7.
Stator
8.
IC voltage regulator assembly
9.
Diode assembly
10. Rear cover
Through bolt:
: 3.5 - 5.3 N·m (0.36 - 0.54 kg-m, 31 - 47 in-lb)
Pulley nut:
: 99 - 137 N·m (10.1 - 14.0 kg-m, 73 - 101 ft-lb)
PKIA1824E
SC-30
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Battery
AKS002EQ
Starter
AKS002ER
Alternator
AKS002ES
Type
80D23R
Capacity
12V - 52AH
Cold cranking current (For reference value)
582A
Type
M2T85171
MITSUBISHI make
Reduction gear type
System voltage
12V
No-load
Terminal voltage
11V
Current
Less than 145A
Revolution
More than 3,300 rpm
Minimum diameter of commutator
31.4 mm (1.236 in)
Minimum length of brush
11.0 mm (0.433 in)
Brush spring tension
30.9 - 37.7 N (3.15 - 3.85 kg, 6.95 - 8.47 lb)
Clearance between bearing metal and armature shaft
Less than 0.2 mm (0.008 in)
Clearance between pinion front edge and pinion stopper
0.5 - 2.0 mm (0.020 - 0.079 in)
Type
A3TG0391
MITSUBISHI make
Nominal rating
12V - 110A
Ground polarity
Negative
Minimum revolution under no-load (When 13.5 V is applied)
Less than 1,000 rpm
Hot output current (When 13.5 V is applied)
More than 31A / 1,300 rpm
More than 90A / 2,500 rpm
More than 102A / 5,000 rpm
Regulated output voltage
14.1 - 14.7V
Minimum length of brush
More than 5.00 mm (0.197 in)
Brush spring pressure
4.8 - 6.1 N (490 - 610 g, 17.28 - 21.51 oz)
Slip ring minimum outer diameter
More than 22.1 mm (0.870 in)
Rotor (Field coil) resistance
1.7 - 2.1
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст