Infiniti M45 (Y34). Manual — part 74
DTC P1752 INPUT CLUTCH SOLENOID VALVE
AT-181
D
E
F
G
H
I
J
K
L
M
A
B
AT
TCM terminal and data are reference value. Measured between each terminal and ground.
Diagnostic Procedure
ACS0048V
1.
CHECK INPUT SIGNALS
With CONSULT-II
1.
Start engine.
2.
Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3.
Read out the value of “I/C SOLENOID” while driving.
Without CONSULT-II
1.
Start engine.
2.
Check voltage between TCM connector and ground.
OK or NG
OK >> GO
TO
6.
NG
>> GO TO 2.
Terminal
No.
Wire
color
Item
Condition
Data (Approx.)
10
R/W
Input clutch sole-
noid valve
When
vehicle
cruises
When the solenoid valve operating (in 1st gear, 2nd gear,
or 3rd gear)
More than 2.0V
When the solenoid valve is not operating (4th gear or 5th
gear)
0V
Item name
Condition
Display value (Approx.)
I/C SOLENOID
Input clutch solenoid
valve operates.
0.6 - 0.8 A
Other conditions
0 - 0.05 A
SCIA4462E
Item
Con-
nector
No.
Terminal
No.
Condition
Data
(Approx.)
Input
clutch
solenoid
valve
F103
10 (R/
W) -
Ground
When
vehicle
cruises
When the solenoid
valve operating (in 1st
gear, 2nd gear, or 3rd
gear)
More than
2V
When the solenoid
valve is not operating
(4th gear or 5th gear)
0V
SCIA4573E
AT-182
DTC P1752 INPUT CLUTCH SOLENOID VALVE
2.
CHECK INPUT CLUTCH SOLENOID VALVE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect A/T unit assembly harness connector at the trans-
mission right side.
3.
Check the resistance between terminal and ground.
OK or NG
OK >> GO
TO
5.
NG
>> GO TO 3.
3.
CHECK TERMINAL CORD ASSEMBLY
1.
Remove oil pan. Refer to
AT-312, "Control Valve Assembly"
2.
Disconnect A/T unit assembly harness connector and control valve assembly harness connector.
3.
Check continuity between A/T unit assembly harness connector
and control valve assembly harness connector.
4.
If OK, check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK VALVE RESISTANCE
Check valve resistance
●
Refer to
AT-183, "Component Inspection"
OK or NG
OK >> GO
TO
6.
NG
>> Replace the control valve assembly. Refer to
AT-312, "Control Valve Assembly"
Solenoid valve
Connector
No.
Terminal No.
Resistance (Approx.)
Input clutch solenoid
valve
F27
6 - Ground
3 - 9
Ω
SCIA1837E
Item
Connector No.
Terminal No. (Wire color)
Continuity
A/T unit assembly
harness connector
F27
6 (R/W)
Yes
Control valve assem-
bly harness connec-
tor
F301
9 (R/W)
SCIA3073E
DTC P1752 INPUT CLUTCH SOLENOID VALVE
AT-183
D
E
F
G
H
I
J
K
L
M
A
B
AT
5.
CHECK POWER SOURCE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector.
3.
Check continuity between A/T unit assembly harness connector
and TCM connector.
4.
If OK, check harness for short to ground and short to power.
5.
Reinstall any part removed.
OK or NG
OK
>> GO TO 6.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK DTC
Perform “DTC Confirmation Procedure”. Refer to
AT-179, "DTC Confirmation Procedure"
.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 7.
7.
CHECK TCM
1.
Check TCM input/output signal. Refer to
AT-86, "TCM Input/Output Signal Reference Values"
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Component Inspection
ACS0048W
INPUT CLUTCH SOLENOID VALVE
Resistance Check
1.
Turn ignition switch OFF.
2.
Remove oil pan. Refer to
AT-312, "Control Valve Assembly"
3.
Disconnect control valve assembly harness connector.
4.
Check resistance between terminal and ground.
5.
If NG, replace control valve assembly. Refer to
.
Item
Connector No.
Terminal No.
(Wire color)
Continuity
TCM
F103
10 (R/W)
Yes
A/T unit assembly harness
connector
F27
6 (R/W)
SCIA1838E
Solenoid Valve
Connector No.
Terminal No.
(Wire color)
Resistance
(Approx.)
Input clutch solenoid
valve
F301
9 (G) - Ground
3 - 9
Ω
SCIA3074E
AT-184
DTC P1752 INPUT CLUTCH SOLENOID VALVE
Operation Check
●
Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal 9 and ground.
SCIA3108E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст