Infiniti M45 (Y34). Manual — part 49
TROUBLE DIAGNOSIS
AT-81
D
E
F
G
H
I
J
K
L
M
A
B
AT
While accelerating
in 5th, engine races
or slippage occurs.
ON vehicle
1. Fluid level and state
2. Line pressure test
3. Accelerator pedal position sensor
4. CAN communication line
5. ATF pressure switch 1 and front brake solenoid valve
6. Control valve assembly
OFF vehicle
7. Torque converter (ATF condition “NG” only. Refer to
8. Oil pump assembly (ATF condition “NG” only. Refer to
.)
9. Front brake [brake band (ATF condition “NG” only. Refer to
10. Input clutch (ATF condition “NG” only. Refer to
11. Gear system (ATF condition “NG” only. Refer to
12. High and low reverse clutch (ATF condition “NG” only. Refer to
Slips at lock-up.
ON vehicle
1. Fluid level and state
2. Line pressure test
3. Engine speed signal
4. Turbine revolution sensor
5. Torque converter clutch solenoid valve
6. CAN communication line
7. Control valve assembly
OFF vehicle
8. Torque converter (ATF condition “NG” only. Refer to
9. Oil pump assembly (ATF condition “NG” only. Refer to
.)
Symptom
Condition
Diagnostic Item
Reference page
AT-82
TROUBLE DIAGNOSIS
Maximum speed
low.
ON vehicle
1. Fluid level and state
2. Line pressure test
3. Accelerator pedal position sensor
4. CAN communication line
5. Direct clutch solenoid valve
6. Control valve assembly
OFF vehicle
7. Torque converter (ATF condition “NG” only. Refer to
.)
8. Oil pump assembly (ATF condition “NG” only. Refer to
9. Input clutch (ATF condition “NG” only. Refer to
10. Gear system (ATF condition “NG” only. Refer to
11. High and low reverse clutch (ATF condition “NG” only. Refer to
12. Direct clutch (ATF condition “NG” only. Refer to
13. Forward one-way clutch* (ATF condition “NG” only. Refer to
14. Forward brake* (ATF condition “NG” only. Refer to
.)
"Vehicle Does Not
Creep Backward in
“R” Position"
268, "Vehicle Does
Not Creep Forward
in “D” Position"
ON vehicle
1. Fluid level and state
2. Line pressure test
3. Accelerator pedal position sensor
4. ATF pressure switch 5 and direct clutch solenoid valve
,
5. PNP switch
6. CAN communication line
7. Control linkage adjustment
8. Control valve assembly
OFF vehicle
9. Torque converter (ATF condition “NG” only. Refer to
.)
10. Oil pump assembly (ATF condition “NG” only. Refer to
11. 1st one-way clutch (ATF condition “NG” only. Refer to
12. Gear system (ATF condition “NG” only. Refer to
13. Reverse brake (ATF condition “NG” only. Refer to
.)
14. Direct clutch (ATF condition “NG” only. Refer to
15. Forward one-way clutch* (ATF condition “NG” only. Refer to
16. Forward brake* (ATF condition “NG” only. Refer to
.)
Symptom
Condition
Diagnostic Item
Reference page
TROUBLE DIAGNOSIS
AT-83
D
E
F
G
H
I
J
K
L
M
A
B
AT
Extremely large
creep.
ON vehicle
1. Engine idle speed
2. CAN communication line
3. ATF pressure switch 5
OFF vehicle
4. Torque converter (ATF condition “NG” only. Refer to
With selector lever
in “P” position, vehi-
cle does not enter
parking condition
or, with selector
lever in another
position, parking
condition is not
cancelled.
Refer to
“P” Position, Vehi-
cle Moves When
Pushed"
ON vehicle
1. PNP switch
2. Control linkage adjustment
3. Parking pawl components (ATF condition “NG” only. Refer to
Vehicle runs with
transmission in “P”
position.
ON vehicle
1. PNP switch
2. Fluid level and state
3. Control linkage adjustment
4. Control valve assembly
5. Parking pawl components (ATF condition “NG” only. Refer to
OFF vehicle
6. Gear system (ATF condition “NG” only. Refer to
Vehicle runs with
transmission in “N”
position.
Refer to
“N” Position, Vehi-
cle Moves"
ON vehicle
1. PNP switch
2. Fluid level and state
3. Control linkage adjustment
4. Control valve assembly
OFF vehicle
5. Input clutch (ATF condition “NG” only. Refer to
6. Gear system (ATF condition “NG” only. Refer to
7. Direct clutch (ATF condition “NG” only. Refer to
8. Reverse brake (ATF condition “NG” only. Refer to
9. Forward one-way clutch* (ATF condition “NG” only. Refer to
10. Low coast brake* (ATF condition “NG” only. Refer to
.)
Symptom
Condition
Diagnostic Item
Reference page
AT-84
TROUBLE DIAGNOSIS
Vehicle cannot run
in all positions.
ON vehicle
1. Fluid level and state
2. Line pressure test
3. PNP switch
4. Control linkage adjustment
5. Control valve assembly
OFF vehicle
6. Oil pump assembly (ATF condition “NG” only. Refer to
7. Gear system (ATF condition “NG” only. Refer to
8. Output shaft (ATF condition “NG” only. Refer to
With selector lever
in “D” position, driv-
ing is not possible.
ON vehicle
1. Fluid level and state
2. Line pressure test
3. PNP switch
4. Control linkage adjustment
5. Control valve assembly
OFF vehicle
6. Torque converter (ATF condition “NG” only. Refer to
.)
7. Oil pump assembly (ATF condition “NG” only. Refer to
8. 1st one-way clutch (ATF condition “NG” only. Refer to
9. Gear system (ATF condition “NG” only. Refer to
10. Reverse brake (ATF condition “NG” only. Refer to
.)
11. Forward one-way clutch* (ATF condition “NG” only. Refer to
12. Forward brake* (ATF condition “NG” only. Refer to
.)
With selector lever
in “R” position, driv-
ing is not possible.
ON vehicle
1. Fluid level and state
2. Line pressure test
3. PNP switch
4. Control linkage adjustment
5. Control valve assembly
OFF vehicle
6. Gear system (ATF condition “NG” only. Refer to
7. Output shaft (ATF condition “NG” only. Refer to
8. Reverse brake (ATF condition “NG” only. Refer to
Can not be
changed to manual
mode.
Refer to
"Cannot Be
Changed to Manual
Mode"
ON vehicle
1. Manual mode switch
2. Turbine revolution sensor
3. CAN communication line
Symptom
Condition
Diagnostic Item
Reference page
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст