Infiniti M45 (Y34). Manual — part 607
INSTRUMENT PANEL ASSEMBLY
IP-11
C
D
E
F
G
H
J
K
L
M
A
B
IP
Removal and Installation
AIS004UU
WORK STEPS
When removing instrument panel and pad, combination meter, display unit or console box assembly, take
steps in the order shown by ( ) numbers below.
( ):number indicates step in removal procedures.
1.
Display unit
2.
Cluster lid C
3.
Front defroster grille (RH)
4.
Front defroster grille (LH)
5.
Combination meter
6.
Cluster lid A
7.
Steering lock escutcheon
8.
Side ventilation (LH)
9.
Steering column cover
10. Instrument panel bracket
11.
Clock
12. Ignition key lamp assembly
13. Knee protector lower
14.
Audio unit
15. Cluster lid center lower
16. Instrument lower driver panel
17.
Ashtray
18. A/T console finisher
19. Cup holder
20.
Center ventilator grille
21. Console box assembly
22. Instrument lower cover
23.
Glove box pin
24. Escutcheon glove box
25. Glove box assembly
26.
Console upper finisher
27. Glove box striker
28. Glove box cover
29.
CD auto changer
30.
Instrument panel reinforcement
bracket
31. Side ventilation (RH)
32.
Instrument panel and pad
Parts
Reference
page
Instrument
panel and pad
Combination
meter
Display unit
Console box
assembly
(A)
Steering lock escutcheon
(1)
(1)
(B)
Steering column cover
(2)
(2)
(C)
Instrument lower driver panel
(3)
(3)
(D)
Cluster lid A
(4)
(4)
(E)
Combination meter
(5)
(5)
(F)
Cluster lid C
(6)
(1)
(G)
Display unit
(7)
(2)
(H)
Clock
(8)
(I)
A/T console finisher
(9)
(1)
(J)
Cup holder
(10)
(2)
(K)
Cluster lid center lower
(11)
(3)
(L)
Console upper finisher
(12)
(4)
(M)
Audio unit
(13)
(N)
Ashtray
(14)
(O)
Instrument lower cover
(15)
(5)
(P)
Glove box assembly
(16)
(6)
(Q)
Glove box cover
(17)
(7)
(R)
CD auto changer
(18)
(S)
Center ventilator grille
(19)
(8)
(T)
Console box assembly
(20)
(9)
(U)
Front defroster grille (LH/RH)
(21)
(V)
Front pillar garnish (LH/RH)
(23)
(W)
Instrument panel bracket
(24)
(X)
Instrument panel reinforcement bracket
(25)
(Y)
Instrument panel and pad
(26)
IP-12
INSTRUMENT PANEL ASSEMBLY
REMOVAL
(A) Steering Lock Escutcheon
Pull back to your side, and disconnect metal clips.
(B) Steering Column Cover
1.
Remove screws with power tool.
2.
Disengage steering position switch connector, then remove steering column cover.
NOTE:
●
Move the steering column telescopic to the rear most position.
●
Move the steering column tilt to the lower bottom position.
(C) Instrument Lower Driver Panel
1.
Remove bolts and nuts with power tool, then remove hood lock
opener lever.
2.
Pull straight to your side, disconnect connectors, and remove
instrument lower driver panel.
(D) Cluster Lid A
1.
Remove screws with power tool.
2.
Pull upper side downward, and disconnect clips.
3.
Make upper and lower side narrower, and pull it back to your
side.
4.
Remove as covering steering wheel.
PIIA2603E
PIIA2612E
PIIA2604E
PIIA2605E
INSTRUMENT PANEL ASSEMBLY
IP-13
C
D
E
F
G
H
J
K
L
M
A
B
IP
(E) Combination Meter
1.
Remove screws with power tool and then disconnect harness
connector.
2.
Pull lower part straight forward and remove location pin.
3.
Push right side of meter rearward and then pull straight forward
on left side.
CAUTION:
To prevent it from being damaged by interference with the
meter bracket, protect the meter with cloths.
(F) Cluster Lid C
1.
Insert a remover, or thin spatula into dip between instrument
panel, pull back to your side, and disconnect metal clips below.
2.
Disconnect harness connectors, and remove.
CAUTION:
Cover surroundings with cloth to avoid scratches or dam-
ages.
(G) Display Unit
1.
Remove screws with power tool.
2.
Disconnect harness connector. Refer to
DI-87, "Removal and Installation of Display"
(H) Clock
1.
Remove screws, push to frontward and remove.
2.
Disconnect harness connector.Refer to
DI-136, "Removal and Installation"
(I) A/T Console Finisher
Open cup holder lid. Hold rear part of A/T console finisher, lift it up,
and disconnect metal clips at its rear end.
(J) Cup Holder
Remove screws with power tool, lift it up, disconnect metal clips at its
rear end, and remove.
PIIA2613E
PIIA2606E
PIIA2608E
PIIA2609E
IP-14
INSTRUMENT PANEL ASSEMBLY
(K) Cluster Lid Center Lower
Open lid of ashtray. Hold lower part of cluster lid center lower, and
pull back to your side. Disconnect both metal clips, and remove.
(L) Console Upper Finisher
Remove screws with power tool, hold front part of console upper finisher, pull back to your side, and discon-
nect clips.
(M) Audio Unit
Remove screws with power tool, disconnect connectors, and remove audio unit. Refer to
and Installation of Audio Unit"
.
(N) Ashtray
1.
Remove screws with power tool, pull back to your side, and dis-
connect metal clips.
2.
Disconnect harness connectors, and remove.
(O) Instrument Lower Cover
1.
Pull down front of instrument lower cover, and disconnect metal
clips.
2.
Pull it horizontally, and remove from lower cover clips.
CAUTION:
Remove connectors of air bag from instrument lower cover.
(P) Glove Box Assembly
1.
Remove clip to outside.
PIIA2607E
PIIA2610E
PIIA2615E
PIIA2614E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст