Infiniti M45 (Y34). Manual — part 325
VOICE ACTIVATED CONTROL SYSTEM
DI-145
C
D
E
F
G
H
I
J
L
M
A
B
DI
Terminals and Reference Values for Voice Activated Control Module
AKS004OU
Terminals
Item
Condition
Reference value
(+)
(–)
Terminal
No.
Wire
color
Terminal
No.
Wire
color
13
SB
Ground
–
Battery power supply
–
Battery voltage
14
B
Ground
–
Ground
–
Approx. 0V
20
L/OR
Ground
–
Ignition switch (ACC)
ACC
Battery voltage
23
–
–
–
Audio shield ground
–
–
25
L
23
–
Audio output (–)
Voice guide operates.
26
R
23
–
Audio output (+)
27
Y/R
Ground
–
Mute
PTT switch (not operate
→
operate)
Approx. 5V
→
Approx. 0V
34
R
33
L
Mic input
Voice mic test
operates.
35
R
37
–
Communication signal (–)
–
36
G
37
–
Communication signal (+)
–
37
–
–
–
Shield ground
–
–
SKIA9342E
SKIA9343E
SKIA0176E
SKIA0175E
DI-146
VOICE ACTIVATED CONTROL SYSTEM
Component Parts and Harness Connector Location
AKS004EC
SKIA9344E
VOICE ACTIVATED CONTROL SYSTEM
DI-147
C
D
E
F
G
H
I
J
L
M
A
B
DI
Trouble Diagnoses
AKS004ED
THIS CONDITION IS NOT MALFUNCTION
Example of Basic Operational Errors
The system should respond correctly to all voice commands. Follow the solutions given in this guide for the
appropriate error when any of the following symptom is encountered.
Where the solutions are listed by number, try each solution in turn, starting with number one, until the symp-
tom is resolved.
Self-Diagnosis Function
AKS004EE
DESCRIPTION
●
Diagnosis function consists of the self-diagnosis mode, and the “CONFIRMATION/ADJUSTMENT” mode.
●
Self-diagnosis mode checks for connection between AV and NAVI control unit (with navigation system) or
AV control unit (without navigation system) and voice activated control module and analyzes each unit,
then displays the results.
●
“CONFIRMATION/ADJUSTMENT” function analyzes each microphone.
DIAGNOSIS ITEM
Self-Diagnosis Mode
AKS004EF
OPERATION PROCEDURE
●
To start the self-diagnosis mode and to check the diagnosis result, refer to
(with navigation system), or
(without navigation system).
Symptom
Remedy
Displays “COMMAND
NOT RECOGNIZED” or
the system does not
interpret the command
correctly.
1. Ensure that the command is valid, see Command list (Refer to Owner’s Manual).
2. Ensure that the command is given after the tone while “ LISTENING” is displayed.
3. Speak clearly without pausing between words and at a level appropriate to the ambient noise level.
4. Ensure that the ambient noise level is not excessive, for example, windows open or defrost on.
NOTE:
If it is too noisy to use the microphone, it is likely that voice commands will not be recognized.
5. If optional words of the command have been omitted, then the command should be tried with these in
place.
6. If a number of commands have been given in rapid succession resulting in the message “COMMAND
NOT RECOGNIZED” to be displayed, then allow the system to recover (approximately one minute)
before trying the command again.
7. If the system consistently does not recognize commands, the voice training procedure should be carried
out to improve the recognition response for the speaker.
Displays “NO SPEECH
DETECTED”.
1. Ensure that the command is given after the tone while “LISTENING” is displayed.
2. Ensure that the command is given within a maximum of five seconds from the end of the tone.
NOTE:
Be sure you know what to say before pressing the PTT switch.
Displays “NAMETAG
NOT UNIQUE”.
1. This response will be received when storing a nametag if the nametag being given has already been
stored. This can be confirmed by giving the Radio Directory command.
2. If this response is received and the nametag has not been used already, then it is too similar to an exist-
ing nametag or voice grammar and an alternative should be used.
The system consistently
selects the wrong
nametag.
1. Ensure that the nametag requested matches what was originally stored. This can be confirmed by giving
the Radio Directory command.
2. Delete one of the nametags being confused and replace it with a different nametag.
Mode
Description
Self-diagnosis
●
Checks for the connections between AV and NAVI control unit or AV control unit and
voice activated control module.
●
Performs the unit diagnosis of voice activated control module.
CONFIRMATION/
ADJUSTMENT
Voice Mic. Test
●
Checks microphone.
DI-148
VOICE ACTIVATED CONTROL SYSTEM
Confirmation/Adjustment Mode
AKS004EG
OPERATION PROCEDURE
1.
Start the engine.
2.
Turn the audio system off.
3.
While pressing the “INFO” switch, turn the volume control dial
clockwise or counterclockwise for 30 clicks or more.
4.
The initial trouble diagnosis screen will be shown, and items
“SELF-DIAGNOSIS” and “CONFIRMATION/ADJUSTMENT” will
become selective.
5.
When “CONFIRMATION/ADJUSTMENT” is selected on the
trouble diagnosis screen, the operation will enter the CONFIR-
MATION/ADJUSTMENT mode. In this mode, check and adjust-
ment of each item will become possible.
6.
When “Voice Mic. Test” is selected with joystick, icon indicator
turns on (green) and voice input into microphone is sent out
through speakers.
NOTE:
Voice from speakers may sound echoic.
SKIA3512E
SKIA0381E
SKIA3922E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст