Infiniti M45 (Y34). Manual — part 714
REAR DRIVE SHAFT
RAX-13
C
E
F
G
H
I
J
K
L
M
A
B
RAX
ASSEMBLY
Final Drive Side
1.
If plug has been removed, use a drift (special service tool) to
press in a new one.
CAUTION:
Discard old plug; replace with new one.
2.
Wind serrated part of shaft with tape. Install boot band and boot
to shaft. Be careful not to damage boot.
CAUTION:
Discard old boot band and boot; replace with new one.
3.
Remove protective tape wound around serrated part of shaft.
4.
Install ball cage/steel ball/inner race assembly to shaft, and
secure them tightly with a snap ring.
CAUTION:
Discard old snap ring; replace with new one.
5.
Insert the amount grease (Nissan genuine grease or equivalent)
onto housing ( * point) to the quantity mentioned below, and
install it to shaft.
6.
Install stopper ring to housing.
7.
After installed, pull shaft to check engagement between joint
sub-assembly and stopper ring.
SDIA1153E
SFA800
SDIA1125E
Reference value
Grease amount
: 124 - 134 g (4.37 - 4.73 oz)
RAC0678D
RAX-14
REAR DRIVE SHAFT
8.
Install boot securely into grooves (indicated by * marks) shown
in the figure.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
9.
Check that boot installation length “L” is the length indicated
below. Insert a flat-bladed screwdriver or similar tool into smaller
side of boot. Remove air from boot to prevent boot deformation.
CAUTION:
●
Boot may break if boot installation length is than standard value.
●
Take care not to touch the tip of screwdriver to inside of boot.
10. Secure big and small ends of boot with new boot bands as
shown in the figure.
CAUTION:
Discard old boot band; replace with new one.
11. After installing housing and shaft, rotate boot to check whether
or not the actual position is correct. If boot position is not correct,
secure boot with new boot band again.
Wheel Side
1.
Insert the amount grease (Nissan genuine grease or equivalent)
into joint sub-assembly serration hole until grease begins to
ooze from ball groove and serration hole. After inserting grease,
use a shop cloth to wipe off old grease that has oozed out.
2.
Wind serrated part of shaft with tape. Install boot band and boot
to shaft. Be careful not to damage boot.
CAUTION:
Discard old boot band and boot; replace with new one.
3.
Remove protective tape wound around serrated part of shaft.
Standard value
Boot installation length “L”
: 93.9 mm (3.697 in)
SDIA1126E
SFA395
SDIA1127E
SFA800
REAR DRIVE SHAFT
RAX-15
C
E
F
G
H
I
J
K
L
M
A
B
RAX
4.
Attach circular clip to shaft. At this time, circular clip must fit
securely into shaft groove. Attach nut to joint sub-assembly. Use
a wooden hammer to press-fit.
CAUTION:
Discard old circular clip; replace with new one.
5.
Apply the grease amount (Nissan genuine grease or equivalent)
listed below into joint sub-assembly from large end of boot.
6.
Install boot securely into grooves (indicated by * marks) shown
in the figure.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and joint sub-assembly, boot may come off.
Remove all grease from surfaces.
7.
Check that boot installation length “L” is the length indicated
below. Insert a flat-bladed screwdriver or similar tool into smaller
side of boot. Remove air from boot to prevent boot deformation.
CAUTION:
●
Boot may brake if boot installation length is than standard value.
●
Be careful that screwdriver tip does not contact inside surface of boot.
8.
Secure big and small ends of boot with new boot bands as
shown in the figure.
CAUTION:
Discard old boot band; replace with new one.
9.
After installing housing and shaft, rotate boot to check whether
or not the actual position is correct. If boot position is not correct,
secure boot with new boot bands again.
Reference value
Grease amount
: 86 - 96 g (3.03 - 3.39 oz)
RAC0049D
Standard value
Boot installation length “L”
: 97 mm (3.82 in)
SDIA1128E
SFA395
RAX-16
SERVICE DATA
SERVICE DATA
PFP:00030
Wheel Bearing
ADS0006O
Drive Shaft
ADS0006P
Z100D90F TYPE
Axial end play limit
0.05 mm (0.002 in) or less
Rotating torque
At a load of 34,324 to 49,033 N (3,500 to 5,000 kg, 7,718 to 11,025 lb)
Less than 1.961 N·m (0.20 kg-m, 17 in-lb)
Measurement of spring scale
Less than 14.7 N (1.5 kg, 32.4 lb)
Measuring point: (Brake caliper installation points)
SDIA1031E
Joint type
Z100 (Wheel side)
D90F (Final drive side)
Grease amount
86 - 96 g (3.03 - 3.39 oz)
124 - 134 (4.37 - 4.73 oz)
Boots installation length
97 mm (3.82 in)
93.9 mm (3.697 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст