Infiniti M45 (Y34). Manual — part 111
ON-VEHICLE SERVICE
AT-329
D
E
F
G
H
I
J
K
L
M
A
B
AT
7.
Install engine rear member. Refer to
.
8.
Install propeller shaft. Refer to
PR-5, "Removal and Installation"
.
9.
AT-304, "Control Device Removal
10. Install exhaust front tube and center muffler with a power tool.
Refer to
EX-3, "Removal and Installation"
11. Install drain plug in oil pan.
CAUTION:
Do not reuse drain plug gasket.
12. Pour ATF into transmission assembly. Refer to
●
After completing installation, check fluid leakage and fluid level of transmission assembly. Refer to
Self-sealing bolt:
: 61 N·m (6.2 kg-m, 45 ft-lb)
: 34 N·m (3.5 kg-m, 25 ft-lb)
SCIA3703E
AT-330
AIR BREATHER HOSE
AIR BREATHER HOSE
PFP:31098
Removal and Installation
ACS001GL
Refer to the figure below for air breather hose removal and installation procedure.
CAUTION:
●
When installing an air breather hose, be careful not to be crushed or blocked by folding or bend-
ing the hose.
●
When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend R portion.
●
When inserting a hose to the air breather tube, be sure to insert it fully until its end reaches the
tube spool portion.
SCIA4722E
TRANSMISSION ASSEMBLY
AT-331
D
E
F
G
H
I
J
K
L
M
A
B
AT
TRANSMISSION ASSEMBLY
PFP:31020
Removal and Installation
ACS001GM
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
Be careful not to damage sensor edge.
1.
Disconnect the battery cable from the negative terminal.
2.
Remove engine under cover with a power tool.
3.
Remove exhaust front tube and center muffler with a power tool. Refer to
EX-3, "Removal and Installation"
.
4.
Remove propeller shaft. Refer to
PR-5, "Removal and Installation"
.
5.
Remove control rod. Refer to
AT-304, "Control Device Removal and Installation"
.
6.
Disconnect A/T unit assembly harness connectors.
7.
Remove crankshaft position sensor (POS) from A/T assembly.
8.
Remove fluid cooler tube and A/T fluid charging pipe.
9.
Plug up openings such as the A/T fluid charging pipe hole, etc.
10. Remove air breather hose. Refer to
AT-330, "Removal and Installation"
.
11. Remove starter motor. Refer to
SC-15, "Removal and Installation"
1.
Transmission assembly
2.
A/T fluid charging pipe
3.
O-ring
4.
Fluid cooler tube
5.
Copper washer
6.
Bracket
7.
Engine rear member
8.
Insulator
9.
Fluid cooler hose
10. Hose band
SCIA4676E
AT-332
TRANSMISSION ASSEMBLY
12. Remove rear plate cover from converter housing part.
13. Turn crankshaft, and remove the four tightening bolts for drive
plate and torque converter.
CAUTION:
When turning crankshaft, turn it clockwise as viewed from
the front of the engine.
14. Support transmission assembly with a transmission jack.
CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug.
15. Remove engine rear member with a power tool.
16. Remove bolts fixing transmission assembly to engine with a power tool.
CAUTION:
Do not perform any work that uses the companion flange
section located at the rear part of the transmission as a
point of support.
17. Remove transmission assembly from vehicle with a transmis-
sion jack.
●
Secure torque converter to prevent it from dropping.
●
Secure transmission assembly to the transmission jack.
PCIA0045J
SCIA0490E
SCIA0499E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст