Infiniti M45 (Y34). Manual — part 733
FRONT LOWER LINK
RSU-13
C
D
F
G
H
I
J
K
L
M
A
B
RSU
FRONT LOWER LINK
PFP:55110
Removal and Installation
AES00092
REMOVAL
1.
Remove tire with power tool.
2.
Set jack under rear lower link.
3.
Remove fixing bolt and nut between front lower link and rear suspension member with power tool.
4.
Remove fixing bolt and nut between front lower link and axle with power tool.
5.
Remove front lower link from vehicle.
INSPECTION AFTER REMOVAL
●
Check front lower link and bushing for any deformation, crack, or damage. Replace if necessary.
INSTALLATION
●
Refer to
for tightening torque. Tighten in the reverse order of removal.
CAUTION:
Refer to component parts location and do not reuse non-reusable parts.
●
Perform final tightening of rear suspension member and axle installation position (rubber bushing) under
unladen condition with tires on level ground. Check wheel alignment. Refer to
.
RSU-14
REAR LOWER LINK & COIL SPRING
REAR LOWER LINK & COIL SPRING
PFP:551B0
Removal and Installation
AES00093
REMOVAL
1.
Remove tire with power tool.
2.
Set jack under rear lower link.
3.
Loosen fixing bolt and nut of rear lower link in side of rear suspension member, and then remove fixing
bolt and nut in side of axle.
4.
Slowly lower jack, then remove upper seat, coil spring and rubber sheet from rear lower link.
5.
Remove fixing bolt and nut in side of rear suspension member to remove rear lower link.
INSPECTION AFTER REMOVAL
●
Check rear lower link, bushing and coil spring for deformation, cracks, and damage. Replace rear lower
link and coil spring if necessary.
INSTALLATION
●
Refer to
for tightening torque. Tighten in the reverse order of removal.
CAUTION:
Refer to component parts location and do not reuse non-reusable parts.
●
Check that the projecting part inside upper seat and the flange
part of bracket are attached as shown in the figure.
●
Check that the projection part outside upper seat directs to vehi-
cle front.
●
Position the hollow of rubber seat with the groove part of rear
lower link to install.
●
Install coil spring with the side of 2 paint markers directing to
lower side.
●
Perform final tightening of rear suspension member and axle installation position (rubber bushing) under
unladen condition with tires on level ground. Check wheel alignment. Refer to
SEIA0266E
STABILIZER BAR
RSU-15
C
D
F
G
H
I
J
K
L
M
A
B
RSU
STABILIZER BAR
PFP:54611
Removal and Installation
AES00094
REMOVAL
1.
Remove dynamic dampener of exhaust tube. Refer to
EX-3, "Removal and Installation"
2.
Remove stabilizer connecting rod from stabilizer bar with power tool.
3.
Remove mounting bolts of stabilizer clamp and then remove stabilizer clamp and stabilizer bushing from
stabilizer bar with power tool.
4.
Remove stabilizer bar from vehicle behind.
INSPECTION AFTER REMOVAL
●
Check stabilizer bar, stabilizer bushing, stabilizer clamp, stabilizer connecting rod, stabilizer connecting
rod mounting bracket for any deformation, crack or damage. Replace if necessary.
INSTALLATION
●
Refer to
for tightening torque. Tighten in the reverse order of removal.
CAUTION:
Refer to component parts location and do not reuse non-reusable parts.
●
Stabilizer bar uses the pillow ball type connecting rod, position
ball joint with case on pillow ball head parallel to stabilizer bar.
SFA449BB
RSU-16
REAR SUSPENSION MEMBER
REAR SUSPENSION MEMBER
PFP:55501
Removal and Installation
AES00095
REMOVAL
1.
Remove tire with power tool.
2.
Remove brake caliper with power tool. Hang it in a place where it will not interfere with work. Refer to
CAUTION:
Avoid depressing brake pedal while brake caliper is removed.
3.
Remove stabilizer bar with power tool. Refer to
4.
Remove rear final drive from vehicle. Refer to
RFD-11, "REAR FINAL DRIVE ASSEMBLY"
5.
Remove parking brake cable from body and rear suspension member. Refer to
.
6.
Set jack under rear lower link.
7.
Remove fixing bolt and nut in the lower side of shock absorber with power tool.
8.
Remove fixing nut in rear suspension member side of suspension arm.
9.
Remove rear lower link and coil spring. Refer to
RSU-14, "REAR LOWER LINK & COIL SPRING"
.
10. Set jack under rear suspension member.
11. Remove fixing bolt in body side of member stay.
12. Remove fixing nuts of rear suspension member with power tool.
13. Slowly jack to remove rear suspension member from vehicle.
14. Remove front lower link from rear suspension member with power tool.
15. Remove radius rod from rear suspension member with power tool.
INSPECTION AFTER REMOVAL
●
Check rear suspension member for deformation, cracks, and other damage and replace if necessary.
INSTALLATION
●
Refer to
for tightening torque. Tighten in the reverse order of removal.
CAUTION:
Refer to component parts location and do not reuse non-reusable parts.
●
Perform final tightening of installation position of links (rubber bushing) under unladen condition with tires
on level ground. Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст