Infiniti M45 (Y34). Manual — part 464
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-545
C
D
E
F
G
H
I
J
K
L
M
A
EC
On Board Diagnosis Logic
ABS002QF
DTC Confirmation Procedure
ABS002QG
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Always perform test at a temperature of 5
°
C (41
°
F) or more.
WITH CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Turn ignition switch ON.
4.
Select “PURG VOL CN/V P1444” of “EVAPORATIVE SYSTEM” in “DTC WORK SUPPORT” mode with
CONSULT-II.
5.
Touch “START”.
6.
Start engine and let it idle until “TESTING” on CONSULT-II changes to “COMPLETED”. (It will take
approximately 10 seconds.)
If “TESTING” is not displayed after 5 minutes, retry from step 2.
7.
Make sure that “OK” is displayed after touching “SELF-DIAG RESULTS”. If “NG” is displayed, refer to
.
WITH GST
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Start engine and let it idle for at least 20 seconds.
4.
Select “MODE 7” with GST.
5.
If 1st trip DTC is detected, go to
EC-547, "Diagnostic Procedure"
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1444
1444
EVAP canister purge
volume control solenoid
valve
The canister purge flow is detected during the
specified driving conditions, even when EVAP
canister purge volume control solenoid valve is
completely closed.
●
EVAP control system pressure sensor
●
EVAP canister purge volume control
solenoid valve
(The valve is stuck open.)
●
EVAP canister vent control valve
●
EVAP canister
●
Water separator
●
Hoses
(Hoses are connected incorrectly or
clogged.)
PBIB0839E
EC-546
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Wiring Diagram
ABS002QH
TBWA0290E
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-547
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
Pulse signal is measured by CONSULT-II.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
Diagnostic Procedure
ABS002QI
1.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE POWER SUPPLY CIR-
CUIT
1.
Turn ignition switch OFF.
2.
Disconnect EVAP canister purge volume control solenoid valve
harness connector.
3.
Turn ignition switch ON.
4.
Check voltage between EVAP canister purge volume control
solenoid valve terminal 1 and ground with CONSULT-II or tester.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
54
L/Y
EVAP canister purge volume
control solenoid valve
[Engine is running]
●
Idle speed
BATTERY VOLTAGE
(11 - 14V)
[Engine is running]
●
Engine speed is about 2,000 rpm (More
than 100 seconds after starting engine).
BATTERY VOLTAGE
(11 - 14V)
PBIB0050E
PBIB0051E
PBIB1120E
Voltage: Battery voltage
PBIB0148E
EC-548
DTC P1444 EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
2.
DETECT MALFUNCTIONING PART
Check the following.
●
Harness connectors E33, F33
●
Fuse, fusible link and relay block (J/B) connector E3
●
10A fuse
●
Harness for open or short between EVAP canister purge volume control solenoid valve and fuse
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OUTPUT SIGNAL CIR-
CUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check harness continuity between ECM terminal 54 and EVAP canister purge volume control solenoid
valve terminal 2. Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR
1.
Disconnect EVAP control system pressure sensor harness connector.
2.
Check connectors for water.
OK or NG
OK
>> GO TO 5.
NG
>> Replace EVAP control system pressure sensor.
5.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Refer to
EC-361, "Component Inspection"
OK or NG
OK (With CONSULT-II)>>GO TO 6.
OK (Without CONSULT-II)>>GO TO 7.
NG
>> Replace EVAP control system pressure sensor.
Continuity should exist.
Water should not exist.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст