Infiniti M45 (Y34). Manual — part 711
RAX-1
REAR AXLE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
RAX
A
B
RAX
REAR AXLE
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Caution . . . . . . . . . . . . . . . . . . 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 4
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 5
NVH Troubleshooting Chart . . . . . . . . . . 5
WHEEL HUB . . . . . . . . . . . . . . . .. 6
On-Vehicle Inspection and Service . . . . . . .. 6
WHEEL BEARING INSPECTION . . . . . . . 6
Removal and Installation . . . . . . . . . . .. 6
REMOVAL . . . . . . . . . . . . . . . . 6
INSPECTION AFTER REMOVAL . . . . . . . 7
INSTALLATION . . . . . . . . . . . . . . 7
Disassembly and Assembly . . . . . . . . . .. 7
REAR DRIVE SHAFT . . . . . . . . . . . ... 10
Removal and Installation . . . . . . . . . . 10
Disassembly and Assembly . . . . . . . . . 11
SERVICE DATA . . . . . . . . . . . . . . 16
Wheel Bearing . . . . . . . . . . . . . . 16
Drive Shaft . . . . . . . . . . . . . . . .. 16
RAX-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Caution
ADS0006G
Observe the following precautions when disassembling and servicing drive shaft.
●
Perform work in a location which is as dust-free as possible.
●
Before disassembling and servicing, clean the outside of parts.
●
Disassembly and service location must be taken to prevent the entry of foreign objects.
●
Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
●
Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
●
Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.
PREPARATION
RAX-3
C
E
F
G
H
I
J
K
L
M
A
B
RAX
PREPARATION
PFP:00002
Special Service Tools
ADS0006H
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV401 04100
( — )
Attachment
Removing wheel hub
ST3623 0000
(J 25840-A)
Sliding hammer
Removing wheel hub
ST33061000
(J 8107-2)
Drift
a: 28.5 mm (1.12 in) dia.
b: 38.0 mm (1.50 in) dia.
Removing wheel bearing outer side inner
race
ST3527 1000
(J 26091)
Drift
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
Removing wheel bearing
KV401 05310
( — )
Drift
a: 75 mm (2.95 in) dia.
b: 62 mm (2.44 in) dia.
Removing wheel bearing
ST3072 0000
(J 25405)
Drift
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
Installing wheel bearing
ZZC0947D
ZZA0803D
ZZA0969D
ZZA0837D
ZZA0832D
ZZA0837D
RAX-4
PREPARATION
Commercial Service Tools
ADS00089
KV401 05220
( — )
Drift
a: 75 mm (2.95 in) dia.
b: 62 mm (2.44 in) dia.
Installing wheel hub
KV381 00500
( — )
Drift
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
Installing drive shaft plug
KV381 02200
( — )
Drift
a: 90 mm (3.54 in) dia.
b: 31 mm (1.22 in) dia.
Installing drive shaft plug
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA0832D
ZZA0701D
ZZA0920D
Tool name
Description
Power tool
●
Removing wheel nuts
●
Removing hub lock nut
●
Removing brake caliper assembly
●
Removing radius rod
●
Removing front lower link
●
Removing shock absorber lower bolt
●
Removing drive shaft
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст