Infiniti M45 (Y34). Manual — part 810
FRONT WIPER AND WASHER SYSTEM
WW-15
C
D
E
F
G
H
I
J
L
M
A
B
WW
SWITCH MONITOR
How to Perform Switch Monitor
Diagnosis Result Display
●
Detects the status change (switch ON/OFF operation) of the switch to be checked, and turns on/off the
indicator lamps (the map lamp and step lamp). Also sounds the buzzer for 0.5 seconds.
●
If a malfunction is detected, no indicator lamp and buzzer react.
Cancel of Switch Monitor
●
Turn ignition switch OFF.
●
Drive the vehicle at more than 7 km/h (4 MPH).
PKIA7882E
SEL960V
WW-16
FRONT WIPER AND WASHER SYSTEM
Intermittent Wiper Does Not Operate
AKS002LH
1.
CHECK INTERMITTENT WIPER SWITCH INPUT SIGNAL
With CONSULT-II
See “INT SW” in “DATA MONITOR” mode.
When wiper switch is in INT position: ON
When wiper switch is in OFF position: OFF
NOTE:
When “DATA MONITOR” is operating, intermittent wiper does not
operate.
Without CONSULT-II
Check wiper switch (INT) in switch monitor mode. Refer to
.
OK or NG
OK
>> GO TO 2
NG
>> Check the following.
●
Front wiper switch
●
Harness for open or short between BCM and wiper switch
●
Front wiper switch ground circuit
2.
CHECK WIPER AUTO STOP SIGNAL
With CONSULT-II
See “WIP AUTO STOP” in “DATA MONITOR” mode, and turn wiper
switch to LO or HI position.
When wiper switch is in INT or OFF position: IGN
When wiper switch is in LO or HI: GND
Without CONSULT-II
1.
Turn ignition switch ON.
2.
Turn wiper switch to LO or HI position.
3.
Check voltage between BCM harness connector E204 terminal
124 (SB) and ground.
OK or NG
OK
>> GO TO 3
NG
>> Check the following.
●
Wiper motor
●
Wiper motor ground circuit
●
Harness for open or short between BCM and wiper motor
SEL503W
SEL504W
Terminals
Voltage
(+)
(-)
Condition
Connector
Terminal (Wire color)
E204
124 (SB)
Ground
Moving
Approx. 0V
Stopped
Battery voltage
PKIA5980E
FRONT WIPER AND WASHER SYSTEM
WW-17
C
D
E
F
G
H
I
J
L
M
A
B
WW
3.
CHECK IGNITION SWITCH ON SIGNAL
With CONSULT-II
See “IGN ON SW” in DATA MONITOR mode.
When ignition switch is ON: ON
When ignition switch is ACC or OFF: OFF
Without CONSULT-II
Check voltage between BCM harness connector M4 terminal 68 (W/
B) and ground.
OK or NG
OK
>> GO TO 4
NG
>> Check the following.
●
10A fuse [No. 1, located in fuse block (J/B) No.1]
●
Harness for open or short between fuse and BCM
4.
CHECK WIPER OPERATION
With CONSULT-II
See “WIPER AMP” in ACTIVE TEST mode. Perform operation
shown on display.
NOTE:
If CONSULT-II is not available, skip this procedure and refer to
OK or NG
OK
>> Replace BCM.
NG
>> GO TO
WW-20, "Wiper and Washer Activate Individu-
ally But Intermittent Wiper and Washer Combination Does Not Operate"
PKIA0311E
Terminals
Voltage
(+)
(-)
Condition
Connector
Terminal
(Wire color)
M4
68 (W/B)
Ground
Ignition switch ON or START
Battery
voltage
Ignition switch ACC or ON
Approx. 0V
PKIA5981E
Wiper motor should operate.
SEL494W
WW-18
FRONT WIPER AND WASHER SYSTEM
Intermittent Time of Wiper Cannot be Adjusted
AKS002LI
1.
CHECK INTERMITTENT WIPER VOLUME INPUT SIGNAL
With CONSULT-II
See “INT RESIST” in “DATA MONITOR” mode while turning intermit-
tent wiper volume.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Measure resistance between BCM harness connector M4 termi-
nal 48 (R/G) and ground while turning intermittent wiper volume.
OK or NG
OK
>> Replace BCM.
NG
>> GO TO 2
2.
CHECK FRONT WIPER SWITCH
Check front wiper switch. Refer to
WW-21, "Wiper and Washer Switch Circuit Check"
.
OK or NG
OK
>> Check the following.
●
Harness for open or short between BCM and front wiper switch
●
Front wiper switch ground circuit
NG
>> Replace front wiper switch.
Wiper and Washer Activate Individually But Not in Combination
AKS002LJ
1.
CHECK WASHER SWITCH INPUT SIGNAL
With CONSULT-II
See “WASH SW” in “DATA MONITOR” mode.
When washer switch is ON: ON
When washer switch is OFF: OFF
Without CONSULT-II
Check wiper switch (WASH) in switch monitor mode. Refer to
.
OK or NG
OK
>> Replace BCM.
NG
>> Check the following.
●
Harness for open or short between BCM and front
wiper switch
Short interval
: Approx. 0 kohm
Long interval
: Approx. 1 kohm
SEL506W
Terminals
Resistance
Connector
Terminal (Wire color)
Condition
M4
48 (R/G)
Ground
Short interval
Approx. 0
Ω
Long interval
Approx. 1k
Ω
PKIA5982E
SEL507W
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст