Infiniti M45 (Y34). Manual — part 369
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
EC-165
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
PFP:226A0
Description
ABS002ES
SYSTEM DESCRIPTION
The ECM performs ON/OFF control of the heated oxygen sensor 2 heater corresponding to the engine speed,
amount of intake air and engine coolant temperature.
OPERATION
CONSULT-II Reference Value in Data Monitor Mode
ABS002ET
Specification data are reference values.
On Board Diagnosis Logic
ABS002EU
Sensor
Input Signal to ECM
ECM function
Actuator
Camshaft position sensor (PHASE)
Engine speed
Heated oxygen sensor 2
heater control
Heated oxygen sensor 2 heater
Crankshaft position sensor (POS)
Engine coolant temperature sensor
Engine coolant temperature
Mass air flow sensor
Amount of intake air
Engine speed rpm
Heated oxygen sensor 2 heater
Above 3,600
OFF
Below 3,600 rpm after the following conditions are met.
●
Engine: After warming up
●
Keeping the engine speed between 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute under no load
ON
MONITOR ITEM
CONDITION
SPECIFICATION
HO2S2 HTR (B1)
HO2S2 HTR (B2)
●
Engine speed: Above 3,600 rpm
OFF
●
Engine speed is below 3,600 rpm after the following conditions are met.
–
Engine: After warming up
–
Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and
at idle for 1 minute under no load
ON
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0037
0037
(Bank 1)
Heated oxygen sensor 2
heater control circuit low
The current amperage in the heated oxygen sensor
2 heater circuit is out of the normal range.
(An excessively low voltage signal is sent to ECM
through the heated oxygen sensor 2 heater.)
●
Harness or connectors
(The heated oxygen sensor 2 heater
circuit is open or shorted.)
●
Heater oxygen sensor 2 heater
P0057
0057
(Bank 2)
P0038
0038
(Bank 1)
Heated oxygen sensor 2
heater control circuit high
The current amperage in the heated oxygen sensor
2 heater circuit is out of the normal range.
(An excessively high voltage signal is sent to ECM
through the heated oxygen sensor 2 heater.)
●
Harness or connectors
(The heated oxygen sensor 2 heater
circuit is shorted.)
●
Heater oxygen sensor 2 heater
P0058
0058
(Bank 2)
EC-166
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
DTC Confirmation Procedure
ABS002EV
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 10.5V and 16V at
idle.
WITH CONSULT-II
1.
Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT-II.
2.
Start the engine and warm it up to the normal operating temperature.
3.
Turn ignition switch OFF and wait at least 10 seconds.
4.
Start engine and keep the engine speed between 3,500 and
4,000 rpm for at least 1 minute.
5.
Let engine idle for 1 minute.
6.
If 1st trip DTC is detected, go to
EC-170, "Diagnostic Procedure"
.
WITH GST
1.
Start the engine and warm it up to the normal operating temperature.
2.
Turn ignition switch OFF and wait at least 10 seconds.
3.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute.
4.
Let engine idle for 1 minute.
5.
Turn ignition switch OFF and wait at least 10 seconds.
6.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute.
7.
Let engine idle for 1 minute.
8.
Select “MODE 3” with GST.
9.
If DTC is detected, go to
EC-170, "Diagnostic Procedure"
.
●
When using GST, DTC Confirmation Procedure should be performed twice as much as when using
CONSULT-II because GST cannot display MODE 7 (1st trip DTC) concerning this diagnosis. There-
fore, using CONSULT-II is recommended.
SEF174Y
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
EC-167
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
ABS002EW
BANK 1
TBWA0269E
EC-168
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
10
GY
Heated oxygen sensor 2
heater (bank 1)
[Engine is running]
●
Engine speed is below 3,600 rpm after the
following conditions are met.
–
Engine: After warming up
–
Keeping the engine speed between 3,500
and 4,000 rpm for 1 minute and at idle for 1
minute under no load
0 - 1.0V
[Ignition switch: ON]
●
Engine stopped
[Engine is running]
●
Engine speed: Above 3,600 rpm.
BATTERY VOLTAGE
(11 - 14V)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст