Infiniti M45 (Y34). Manual — part 263
REAR DISC BRAKE
BR-31
C
D
E
G
H
I
J
K
L
M
A
B
BR
CAUTION:
When replacing the pads with new ones, press in the piston until the pads can be installed. In this
case, carefully monitor the brake fluid level in the reservoir tank because the brake fluid will return
to the reservoir tank of the master cylinder.
4.
Insert the lower sliding pin bolt to tighten to the specified torque.
5.
Check the brake for drag.
6.
Attach the tires to the vehicle.
Removal and Installation of Caliper Assembly
AFS000KN
REMOVAL
1.
Remove tire from vehicle.
2.
Connect a vinyl tube to the bleed valve.
3.
Drain brake fluid gradually from the bleed valve while depress-
ing the brake pedal. Refer to
.
4.
Remove the union bolts, and then remove the brake hose from
the caliper assembly.
5.
Remove the mounting bolts from the torque member, and
remove the caliper assembly from the vehicle.
6.
Remove the disc rotor.
INSTALLATION
1.
Install the disc rotor.
2.
Install the caliper assembly to the vehicle, and tighten the mounting bolts to the specified torque.
CAUTION:
Before installing the caliper assembly to the vehicle, wipe oil and grease on the washer seats on
the axle assembly and mounting surface of the caliper assembly.
3.
Install the brake hose to the caliper assembly and tighten the union bolts to the specified torque.
CAUTION:
●
Do not reuse the copper washer for union bolts.
●
Assemble the brake hose securely to the protrusion on caliper assembly.
4.
After installing the caliper assembly, refill with new brake fluid and bleed air. Refer to
5.
Attach the tires to the vehicle.
Disassembly and Assembly of Caliper Assembly
AFS000KO
DISASSEMBLY
1.
Remove the sliding pin bolts. Then remove the pads, shims, and shim covers from the caliper assembly,
and remove the pad retainers from the cylinder body.
2.
Remove the sliding pin and sliding pin boot from the torque member.
3.
Using a flat-bladed screwdriver as shown in the figure, remove
the retaining ring from the cylinder body.
4.
Place a wooden block as shown in the figure, and blow air from the union bolt mounting hole to remove
the pistons and piston boots.
SFIA0143E
SBR028A
BR-32
REAR DISC BRAKE
CAUTION:
Do not get fingers caught in the piston.
5.
Using a flat-bladed screwdriver, remove the piston seals from
the cylinder body.
CAUTION:
Be careful not to damage the inner wall of the cylinder.
BRD0041D
SFIA2169E
REAR DISC BRAKE
BR-33
C
D
E
G
H
I
J
K
L
M
A
B
BR
INSPECTION AFTER DISASSEMBLY
Cylinder Body
CAUTION:
Use new brake fluid to clean. Never use mineral oils such as gasoline or kerosene.
●
Check the inner wall of the cylinder for corrosion, wear, and damage. If a malfunction is detected, replace
the cylinder body.
●
Minor flaws caused by corrosion or foreign material can be removed by polishing the surface with a fine
sandpaper. Replace the cylinder body, if necessary.
Torque Member
Check for wear, cracks, and damage. If a malfunction is detected, replace the applicable part.
Piston
CAUTION:
The piston sliding surface is plated. Do not polish with sandpaper.
Check the piston surface for corrosion, wear, and damage. If a malfunction is detected, replace the applicable
part.
Sliding Pin, Pin Bolt, and Pin Boot
Check the sliding pin and sliding pin boot for wear, damage, and cracks. If a malfunction is detected, replace
the applicable part.
ASSEMBLY
CAUTION:
Do not use Nissan Rubber Grease (KRE00 00010, KRE00 00010 01) when assembling.
1.
Apply brake grease to the piston seals, and install them to the
cylinder body.
CAUTION:
Do not reuse the piston seals.
2.
Apply brake fluid to piston boots. Cover the piston end with the
piston boot, and install the cylinder-side lip on the piston boots
properly into the groove on the cylinder body.
CAUTION:
Do not reuse the piston boot.
3.
Press the piston into the cylinder body by hand to assemble the
piston-side lip on the piston boot properly into the groove on the
piston.
CAUTION:
Press the piston evenly and change the pressing point to
prevent the inner wall of the cylinder from being rubbed.
SFIA2170E
SFIA2171E
BR-34
REAR DISC BRAKE
4.
Fix the piston boot with the retaining ring.
CAUTION:
●
Make sure that the boot is securely engaged in the
groove on the cylinder body.
●
Do not reuse the retaining ring.
5.
Install the sliding pins and sliding pin boots to the torque mem-
ber.
6.
Install the pad retainers to the torque member.
7.
After assembling the shims and shim covers to the pads,
assemble it to the torque member.
8.
Install the cylinder body, and tighten the sliding pin bolts to the
specified torque.
DISC ROTOR INSPECTION
Visual Inspection
Check the surface of the disc rotor for uneven wear, cracks, and serious damage. If a malfunction is detected,
replace the applicable part.
Runout Inspection
1.
Using wheel nuts, fix the disc rotor to the wheels hub. (2 or more positions)
2.
Using a dial indicator, check the runout.
CAUTION:
Before measuring, make sure that the axle end play is 0 mm
(0 in).
3.
If the runout is outside the limit, find the minimum runout point by
shifting the mounting positions of the disc rotor and wheel hub by one hole.
Thickness Inspection
Using a micrometer, check the thickness of the disc rotor. If the thick-
ness is outside the standard, replace the disc rotor.
Brake Burnishing Procedure
AFS0029W
Burnish the brake contact surfaces according to the following procedure after refinishing or replacing drums or
rotors, after replacing pads or linings, or if a soft pedal occurs at very low mileage.
CAUTION:
Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1.
Drive the vehicle on a straight smooth road at 50 km/h (31 MPH).
2.
Use medium brake pedal/foot effort to bring the vehicle to a complete stop from 50 km/h (31 MPH). Adjust
brake pedal/foot pressure such that vehicle stopping time equals 3 to 5 seconds.
3.
To cool the brake system, drive the vehicle at 50 km/h (31 MPH) for 1 minute without stopping.
4.
Repeat steps 1 to 3, 10 times or more to complete the burnishing procedure.
SFIA2172E
Measurement point:
At a point 10 mm (0.39 in) from the outer
edge of the disc
Maximum runout:
0.10 mm (0.0039 in) or less
BRA0013D
Standard thickness
: 16.0 mm (0.63 in)
Wear limit
: 14.0 mm (0.55 in)
Maximum uneven wear (measured at 8 positions):
0.015 mm (0.0006 in) or less
SBR020B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст