Infiniti M45 (Y34). Manual — part 807
PRECAUTION
WW-3
C
D
E
F
G
H
I
J
L
M
A
B
WW
PRECAUTION
PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AKS004VC
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Wiring Diagrams and Trouble Diagnosis
AKS002L7
When you read wiring diagrams, refer to the following:
●
Refer to
GI-14, "How to Read Wiring Diagrams"
●
Refer to
for power distribution circuit.
When you perform trouble diagnosis, refer to the following:
●
Refer to
GI-10, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES"
●
Refer to
GI-26, "How to Perform Efficient Diagnosis for an Electrical Incident"
.
WW-4
FRONT WIPER AND WASHER SYSTEM
FRONT WIPER AND WASHER SYSTEM
PFP:28810
Component Parts and Harness Connector Location
AKS002L9
System Description
AKS002L8
Through the adoption of vehicle speed detect-type intermittent wiper, Front Wiper System changes wiper's
intermittent time when the engine is stopped and while driving.
Vehicle speed signal is send from the combination meter to BCM. BCM controls intermittent activation time
and coupled activation of washer and wiper.
WIPER OPERATION
Description
The wiper switch is controlled by a lever built in the combination switch.
There are three wiper switch positions
●
LO speed
●
HI speed
●
INT (intermittent)
Power is supplied at all times
●
through 10A fuse [No.3, located in fuse block (J/B) No.1]
●
to BCM terminal 105
With the ignition switch in the ON position, power is supplied
●
through 10A fuse [No. 1, located in fuse block (J/B) No.1]
●
to BCM terminal 68
●
through 20A fuse [No. 34, located in fuse block (J/B) No.2]
●
to front wiper motor terminal 4
PKIA6947E
FRONT WIPER AND WASHER SYSTEM
WW-5
C
D
E
F
G
H
I
J
L
M
A
B
WW
●
to front wiper relay terminal 1
●
to front washer motor terminal 1.
Ground is supplied
●
to front wiper switch terminals 17 and 20
●
through grounds M25 and M115.
Low (MIST) and High Speed Wiper Operation
When the wiper switch is placed in the LO or MIST position, ground is supplied
●
through front wiper switch terminal 14
●
to front wiper motor terminal 6.
With power and ground supplied, the front wiper motor operates at low speed.
When the front wiper switch is placed in the HI position, ground is supplied
●
through front wiper switch terminal 16
●
to front wiper motor terminal 5.
With power and ground supplied, the front wiper motor operates at high speed.
Auto Stop Operation
When the front wiper switch is placed in the OFF position, the front wiper motor will continue to operate until
the wiper arms reach the base of the windshield (Auto stop). When the front wiper switch is placed in the OFF
position, ground is supplied
●
from front wiper switch terminal 14
●
to front wiper motor terminal 6, in order to continue front wiper motor operation at low speed.
Ground is also supplied until the wiper arms reaches the base of the windshield
●
through front wiper switch terminal 13
●
to front wiper relay terminal 3
●
through front wiper relay terminal 4
●
to front wiper motor terminal 3
●
through front wiper motor terminal 1, and
●
through grounds E24, E42 and E62.
When the wiper arms reach the base of the windshield, the switch in the front wiper motor moves to the
“STOP” position. The ground path is interrupted and the front wiper motor stops.
Intermittent Operation
Intermittent operation is controlled by the BCM. When the front wiper switch is placed in the INT position,
ground is supplied
●
to BCM terminal 9
●
through front wiper switch terminal 15
●
to grounds M25 and M115
●
through front wiper switch terminal 17.
The desired interval time is input
●
to BCM terminal 48
●
through front wiper switch terminal 19
●
to BCM terminal 49
●
through combination meter terminal 38 (vehicle speed pulse).
The desired interval time is input
●
to front wiper relay terminal 2
●
through BCM terminal 128.
With power and ground supplied, the front wiper relay is activated. When activated, an intermittent ground is
supplied
●
to front wiper motor terminal 6
●
through front wiper switch terminal 14
●
to front wiper switch terminal 13
WW-6
FRONT WIPER AND WASHER SYSTEM
●
through front wiper relay terminal 3
●
to front wiper relay terminal 5
●
through grounds E24, E42 and E62.
Front wiper motor operates at desired interval with BCM terminal 9 grounded. Intermittent operation can be
adjusted from: Approx. 0.9 - 45 sec.: (when vehicle is stopped), Approx. 0.4 - 30 sec.: (when vehicle is mov-
ing). Judgement on vehicle stopped or moving: Stopped, Moving: More than 5 km/h (3 MPH) Moving, Stopped:
Less than 2 km/h (1 MPH)
WASHER OPERATION
With the ignition switch in the ON position, power is supplied
●
through 20A fuse [No. 34, located in fuse block (J/B) No.2]
●
to front washer motor terminal 1.
When the lever is pulled to the WASH position, ground is supplied
●
to front washer motor terminal 2, and
●
to BCM terminal 4
●
from front wiper switch terminal 18
●
through front wiper switch, terminal 17, and
●
through grounds M25 and M115.
With power and ground supplied, the front washer motor operates. The front wiper motor operates at low
speed for about 3 seconds. This feature is controlled by the BCM in the same manner as the intermittent oper-
ation.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст