Infiniti M45 (Y34). Manual — part 66
DTC P1703 TRANSMISSION CONTROL MODULE (ROM)
AT-149
D
E
F
G
H
I
J
K
L
M
A
B
AT
Diagnostic Procedure
ACS001BX
1.
CHECK DTC
With CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “SELF DIAG RESULTS” mode for “A/T” with CONSULT-
II.
3.
Touch “ERASE”.
4.
Turn ignition switch OFF and wait at least 10 seconds.
5.
Perform DTC confirmation procedure,
Is the “TCM·ROM” displayed again?
YES
>> Replace TCM.
NO
>> INSPECTION END
SCIA5304E
AT-150
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)
PFP:31036
Description
ACS001BY
The TCM consists of a microcomputer and connectors for signal
input and output and for power supply. The TCM controls the A/T.
On Board Diagnosis Logic
ACS001BZ
●
This is not an OBD-II self-diagnostic item.
●
Diagnostic trouble code “TCM·EEPROM” with CONSULT-II is detected when TCM memory EEPROM is
malfunctioning.
Possible Cause
ACS001C0
TCM
DTC Confirmation Procedure
ACS001C1
NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “DATA MONITOR” mode for A/T with CONSULT-II.
3.
Start engine.
4.
Run engine for at least 2 consecutive seconds at idle speed.
5.
If DTC is detected, go to
AT-151, "Diagnostic Procedure"
SCIA1287E
SAT014K
DTC P1704 TRANSMISSION CONTROL MODULE (EEPROM)
AT-151
D
E
F
G
H
I
J
K
L
M
A
B
AT
Diagnostic Procedure
ACS001C2
1.
CHECK DTC
With CONSULT-II
1.
Turn ignition switch ON and select “SELF DIAGNOSIS” mode
for “A/T” with CONSULT-II.
2.
Move selector lever to “R” position.
3.
Depress accelerator pedal (Full throttle position).
4.
Touch “ERASE”.
5.
Turn ignition switch OFF and wait at least 10 seconds.
6.
Perform “DTC Confirmation Procedure”. Refer to
Is the “TCM·EEPROM” displayed again?
YES
>> Replace TCM.
NO
>> INSPECTION END
SCIA5304E
AT-152
DTC P1705 THROTTLE POSITION SENSOR
DTC P1705 THROTTLE POSITION SENSOR
PFP:22620
Description
ACS001C3
Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle
position sensor, etc. The actuator sends a signal to the ECM, and ECM sends signals to TCM with CAN com-
munication.
CONSULT-II Reference Value
ACS004PC
On Board Diagnosis Logic
ACS001C4
●
This is not an OBD-II self-diagnostic item.
●
Diagnostic trouble code “TP SEN/CIRC A/T” with CONSULT-II or 15th judgement flicker without CON-
SULT-II is detected when TCM does not receive the proper accelerator pedal position signals (input by
CAN communication) from ECM.
Possible Cause
ACS001C5
Harness or connectors
(The sensor circuit is open or shorted.)
DTC Confirmation Procedure
ACS001C6
NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1.
Turn ignition switch ON. (Do not start engine.)
2.
Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3.
Start engine and let it idle for 1 second.
4.
If DTC is detected, go to “
AT-153, "Diagnostic Procedure"
Item name
Condition
Display value (Approx.)
ACCELE POSI
Released accelerator pedal.
0.0/8
Fully depressed accelerator pedal.
8/8
SAT014K
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст