Infiniti M45 (Y34). Manual — part 584
FRONT DOOR GLASS AND REGULATOR
GW-47
C
D
E
F
G
H
J
K
L
M
A
B
GW
FRONT DOOR GLASS AND REGULATOR
PFP:80300
Removal and Installation
AIS001GP
REMOVAL
1.
Remove front door finisher. Refer to
2.
Remove door speaker. Refer to
AV-30, "Removal and Installation of Door Speaker"
3.
Remove front door outside molding. Refer to
.
4.
Remove door sealing screen assembly.
5.
Remove door inner cover. Refer to
GW-117, "Removal and Installation"
.
6.
Remove glass stopper and inner stabilizer.
PIIB1566E
1.
Front door glass
2.
Glass stopper
3.
Guide channel
4.
Regulator assembly
5.
Glass guide
6.
Main channel
7.
Sub channel
8.
Guide rail
9.
Inner stabilizer
PIIA3163E
GW-48
FRONT DOOR GLASS AND REGULATOR
7.
Operate power window main switch to raise/lower door window
until glass mounting nuts can be seen.
8.
Remove glass mounting nuts.
9.
While holding door glass, raise it at the rear end to pull the guide roller out of guide rail.
10. Remove glass guide from glass channel while lifting the whole and detach glass.
11. Remove bolt and nut of guide rail then remove guide rail.
12. Disconnect harness connector and clip harness.
13. Remove bolt of regulator assembly then remove regulator
assembly.
14. Remove bolt and nut of guide channel then remove guide chan-
nel.
INSTALLATION
Install in the reverse order of removal.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace it or apply multi-pur-
pose grease.
●
Gear wear
●
Spring damage
●
Regulator deformation
●
Grease condition for each sliding part
SETTING AFTER INSTALLATION
Setting of Limit Switch
If any of the following work has been done, set the limit switch (integrated in the motor).
●
Removal and installation of the regulator.
●
Removal and installation of the motor from the regulator.
●
Operate the regulators as a unit.
●
Removal and installation of the glass.
●
Removal and installation of the glass stopper.
PIIA3164E
PIIA3165E
FRONT DOOR GLASS AND REGULATOR
GW-49
C
D
E
F
G
H
J
K
L
M
A
B
GW
Resetting
After installing each component to the vehicle and adjusting the glass fitting, follow the steps below.
1.
Raise the glass to the top position.
2.
While pressing and holding the reset switch, lower the glass to
the bottom position.
3.
Release the reset switch, and check that the reset switch returns
to the original position, and then raise the glass to the top posi-
tion.
CAUTION:
Do not operate the glass automatically to raise the glass to
the top position.
FITTING INSPECTION
●
Check that the glass is securely fit into the body side weatherstrip.
●
Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the weath-
erstrip is parallel. If the clearance between the glass and weatherstrip is not parallel, adjust glass fitting.
PIIA3169E
GW-50
FRONT DOOR GLASS AND REGULATOR
Door Glass Fitting Adjustment
AIS001Q0
The door glass is properly adjusted using the following five methods:
[A] In-out adjustment (at the glass waist).
[B] Fore-aft tilt adjustment.
[C] In-out tilt adjustment.
[D] Up-stop adjustment.
[E] Fore-aft adjustment.
NOTE:
●
When adjusting the door glass, it is not necessary to
remove the outside door molding.
●
After completing door glass adjustment, retighten all lock
nuts.
ADJUSTMENT LOCATIONS
ADJUSTMENT STANDARD CLEARANCE
PIIA3152E
PIIA3153E
PIIA3150E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст