2017 Infiniti QX70/FX (2017 year). Manual — part 27
(427,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
SCE0504
2. Loosen each wheel nut one or two turns
by turning counterclockwise with the
wheel nut wrench. Do not remove the
wheel nuts until the tire is off the
ground.
3. Carefully raise the vehicle until the tire
clears the ground. To lift the vehicle,
securely hold the jack lever and rod
with both hands as shown above.
Remove the wheel nuts, and then
remove the tire.
SCE0661
Installing the spare tire
The T-type spare tire is designed for
emergency use. (See specific instructions
under the heading “Wheels and tires” (P.8-
26).)
1. Clean any mud or dirt from the surface
between the wheel and hub.
2. Carefully put the spare tire on and
tighten the wheel nuts finger tight.
3. With the wheel nut wrench, tighten
wheel nuts alternately and evenly in the
sequence illustrated (
*
1
,
*
2
,
*
3
,
*
4
,
*
5
) until they are tight.
In case of emergency
6-7
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(428,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
6-8
In case of emergency
4. Lower the vehicle slowly until the tire
touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence illu-
strated. Lower the vehicle completely.
WARNING
.
Incorrect wheel nuts or improperly tigh-
tened wheel nuts can cause the wheel to
become loose or come off. This could
cause an accident.
.
Do not use oil or grease on the wheel
studs or nuts. This could cause the nuts
to become loose.
.
Retighten the wheel nuts when the
vehicle has been driven for 600 miles
(1,000 km) (also in cases of a flat tire,
etc.).
.
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
80 ft-lb (108 N·m)
The wheel nuts must be kept tigh-
tened to specification at all times. It
is recommended that wheel nuts be
tightened to specifications at each
lubrication interval.
.
Adjust tire pressure to the COLD
pressure.
COLD pressure:
After the vehicle has been parked for
three hours or more or driven less
than 1 mile (1.6 km).
COLD tire pressures are shown on
the Tire and Loading Information
label affixed to the driver side center
pillar.
After adjusting tire pressure to the COLD
tire pressure, the display of the tire
pressure information may show higher
pressure than the COLD tire pressure after
the vehicle has been driven more than 1
mile (1.6 km). This is because the tire
pressurizes as the tire temperature rises.
This does not indicate a system malfunc-
tion.
Stowing the damaged tire and tools
1. Securely store the damaged tire, jack
and tools in the storage area.
2. Close the luggage floor cover.
3. Close the lift gate.
WARNING
.
Always make sure that the spare tire and
jacking equipment are properly secured
after use. Such items can become dan-
gerous projectiles in an accident or
sudden stop.
.
The T-type spare tire and small size
spare tire are designed for emergency
use. See specific instructions under the
heading “Wheels and tires” (P.8-26).
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(429,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
To start your engine with a booster battery,
the instructions and precautions below
must be followed.
WARNING
.
If done incorrectly, jump starting can
lead to a battery explosion, resulting in
severe injury or death. It could also
damage your vehicle.
.
Explosive hydrogen gas is always pre-
sent in the vicinity of the battery. Keep
all sparks and flames away from the
battery.
.
Do not allow battery fluid to come into
contact with eyes, skin, clothing or
painted surfaces. Battery fluid is a
corrosive sulphuric acid solution which
can cause severe burns. If the fluid
should come into contact with anything,
immediately flush the contacted area
with water.
.
Keep the battery out of the reach of
children.
.
The booster battery must be rated at 12
volts. Use of an improperly rated battery
can damage your vehicle.
.
Whenever working on or near a battery,
always wear suitable eye protectors (for
example, goggles or industrial safety
spectacles) and remove rings, metal
bands, or any other jewelry. Do not lean
over the battery when jump starting.
.
Do not attempt to jump start a frozen
battery. It could explode and cause
serious injury.
.
Your vehicle has an automatic engine
cooling fan. It could come on at any time.
Keep hands and other objects away from
it.
In case of emergency
6-9
JUMP STARTING
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(430,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
6-10
In case of emergency
SCE0772
WARNING
Always follow the instructions below. Fail-
ure to do so could result in damage to the
charging system and cause personal injury.
1. Remove the engine compartment cover,
if necessary. See “Engine compartment
check locations” (P.8-3).
2. If the booster battery is in another
vehicle
*
A
, position the two vehicles
(
*
A
and
*
B
) to bring their batteries
into close proximity to each other.
Do not allow the two vehicles to touch.
3. Apply parking brake. Move the shift
lever to the P (Park) position. Switch off
all unnecessary electrical systems
(light, heater, air conditioner, etc.).
4. Remove vent caps on the battery (if so
equipped). Cover the battery with a
firmly wrung out moist cloth
*
C
to
reduce explosion hazard.
5. Connect jumper cables in the sequence
illustrated (
*
1
?
*
2
?
*
3
?
*
4
).
CAUTION
.
Always connect positive (+) to positive
(+) and negative (−) to body ground (as
illustrated) — not to the battery.
.
Make sure the jumper cables do not
touch moving parts in the engine com-
partment and that clamps do not contact
any other metal.
6. Start the engine of the booster vehicle
*
A
and let it run for a few minutes.
7. Keep the engine speed of the booster
vehicle
*
A
at about 2,000 rpm, and
start the engine of the vehicle being
jump started
*
B
.
CAUTION
Do not keep the starter motor engaged for
more than 10 seconds. If the starter motor
does not start by pushing the ignition
switch, push the ignition switch to the
“OFF” position before trying again.
8. After starting your engine, carefully
disconnect the negative cable and then
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(431,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
the positive cable (
*
4
?
*
3
?
*
2
?
*
1
).
9. Replace the vent caps (if so equipped).
Be sure to dispose of the cloth used to
cover the vent holes as it may be
contaminated with corrosive acid.
10.Put the battery cover on.
Do not attempt to start the engine by
pushing.
CAUTION
.
Automatic transmission models cannot
be push-started or tow-started. Attempt-
ing to do so may cause transmission
damage.
.
Three way catalyst equipped models
should not be started by pushing since
the three way catalyst may be damaged.
.
Never try to start the vehicle by towing
it; when the engine starts, the forward
surge could cause the vehicle to collide
with the tow vehicle.
CAUTION
.
Do not continue to drive if your vehicle
overheats. Doing so could cause engine
damage or a vehicle fire.
.
To avoid the danger of being scalded,
never remove the radiator cap while the
engine is still hot. When the radiator cap
is removed, pressurized hot water will
spurt out, possibly causing serious
injury.
.
Do not open the hood if steam is coming
out.
If your vehicle is overheating (indicated by
an extremely high temperature gauge
reading), or if you feel a lack of engine
power, detect abnormal noise, etc., take
the following steps:
1. Move the vehicle safely off the road,
apply the parking brake and move the
shift lever to the P (Park) position.
Do not stop the engine.
2. Turn off the climate control. Open all
the windows, move the heater or air
conditioner temperature control to
maximum hot and fan control to high
In case of emergency
6-11
PUSH STARTING
IF YOUR VEHICLE OVERHEATS
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(432,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
6-12
In case of emergency
speed.
3. If engine overheating is caused by
climbing a long hill on a hot day, run
the engine at a fast idle (approximately
1,500 rpm) until the temperature gauge
indication returns to normal.
4. Get out of the vehicle. Look and listen
for steam or coolant escaping from the
radiator before opening the hood. (If
steam or coolant is escaping, turn off
the engine.) Do not open the hood
further until no steam or coolant can be
seen.
5. Open the engine hood.
WARNING
If steam or water is coming from the engine,
stand clear to prevent getting burned.
6. Visually check drive belts for damage or
looseness. Also check if the cooling fan
is running. The radiator hoses and
radiator should not leak water. If cool-
ant is leaking or the cooling fan does
not run, stop the engine.
WARNING
Be careful not to allow your hands, hair,
jewelry or clothing to come into contact
with, or get caught in, engine belts or the
engine cooling fan. The engine cooling fan
can start at any time.
7. After the engine cools down, check the
coolant level in the reservoir tank with
the engine running. Add coolant to the
reservoir tank if necessary. Have your
vehicle repaired. It is recommended
you visit an INFINITI retailer for this
service.
When towing your vehicle, all State (Pro-
vincial in Canada) and local regulations for
towing must be followed. Incorrect towing
equipment could damage your vehicle.
Towing instructions are available from an
INFINITI retailer. Local service operators are
familiar with the applicable laws and
procedures for towing. To assure proper
towing and to prevent accidental damage
to your vehicle, INFINITI recommends that
you have a service operator tow your
vehicle. It is advisable to have the service
operator carefully read the following pre-
cautions.
WARNING
.
Never ride in a vehicle that is being
towed.
.
Never get under your vehicle after it has
been lifted by a tow truck.
CAUTION
.
When towing, make sure that the trans-
mission, axles, steering system and
powertrain are in working condition. If
any unit is damaged, dollies must be
TOWING YOUR VEHICLE
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(433,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
used.
.
Always attach safety chains before tow-
ing.
For information about towing your vehicle
behind a recreational vehicle (RV), see
“Flat towing” (P.10-27) of this manual.
SCE0768
Two-wheel drive models
TOWING RECOMMENDED BY
INFINITI
Two-Wheel Drive (2WD) models
INFINITI recommends that your vehicle be
towed with the driving (rear) wheels off the
ground or place the vehicle on a flat bed
truck as illustrated.
CAUTION
.
Never tow automatic transmission mod-
els with the rear wheels on the ground or
four wheels on the ground (forward or
backward), as this may cause serious
and expensive damage to the transmis-
sion. If it is necessary to tow the vehicle
with the front wheels raised, always use
towing dollies under the rear wheels.
.
When towing rear wheel drive models
with the front wheels on the ground or
on towing dollies: Push the ignition
switch to the ACC or ON position, and
secure the steering wheel in a straight-
ahead position with a rope or similar
device.
In case of emergency
6-13
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(434,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
6-14
In case of emergency
SCE0736
All-wheel drive models
All-Wheel Drive (AWD) models
INFINITI recommends that towing dollies be
used when towing your vehicle or the
vehicle be placed on a flat bed truck as
illustrated.
CAUTION
Never tow AWD models with any of the
wheels on the ground as this may cause
serious and expensive damage to the
powertrain.
VEHICLE RECOVERY (freeing a stuck
vehicle)
WARNING
To avoid vehicle damage, serious personal
injury or death when recovering a stuck
vehicle:
.
Contact a professional towing service to
recover the vehicle if you have any
questions regarding the recovery proce-
dure.
.
Tow chains or cables must be attached
only to main structural members of the
vehicle.
.
Do not use the vehicle tie-downs to tow
or free a stuck vehicle.
.
Only use devices specifically designed
for vehicle recovery and follow the
manufacturer’s instructions.
.
Always pull the recovery device straight
out from the front of the vehicle. Never
pull at an angle.
.
Route recovery devices so they do not
touch any part of the vehicle except the
attachment point.
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(435,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
If your vehicle is stuck in sand, snow, mud,
etc., use a tow strap or other device
designed specifically for vehicle recovery.
Always follow the manufacturer’s instruc-
tions for the recovery device.
Rocking a stuck vehicle
If your vehicle is stuck in sand, snow, mud,
etc., use the following procedure:
1. Turn off the Vehicle Dynamic Control
(VDC) system.
2. Make sure the area in front and behind
the vehicle is clear of obstructions.
3. Turn the steering wheel right and left to
clear an area around the front tires.
4. Slowly rock the vehicle forward and
backward.
.
Shift back and forth between R
(reverse) and D (drive).
.
Apply the accelerator as little as
possible to maintain the rocking
motion.
.
Release the accelerator pedal before
shifting between R and D.
.
Do not spin the tires above 35 MPH
(55 km/h).
5. If the vehicle cannot be freed after a few
tries, contact a professional towing
service to remove the vehicle.
In case of emergency
6-15
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(436,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
6-16
In case of emergency
MEMO
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(437,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
7 Appearance and care
Washing . . . . . . . . . . . . . . . 7-2
Waxing . . . . . . . . . . . . . . ... 7-2
Removing spots . . . . . . . . . . . .. 7-3
Underbody . . . . . . . . . . . . . . 7-3
Glass . . . . . . . . . . . . . . . .. 7-3
Wheels . . . . . . . . . . . . . . ... 7-3
Chrome parts . . . . . . . . . . . . . 7-4
Tire dressing . . . . . . . . . . . . .. 7-4
Cleaning interior . . . . . . . . . . . . 7-4
Air fresheners . . . . . . . . . . . ... 7-5
Floor mats . . . . . . . . . . . . . 7-5
Seat belts . . . . . . . . . . . . . . 7-6
Corrosion protection . . . . . . . . . . ... 7-7
Most common factors contributing to
vehicle corrosion . . . . . . . . . . .. 7-7
Environmental factors influence the rate
of corrosion . . . . . . . . . . . . .. 7-7
To protect your vehicle from corrosion . . .. 7-7
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(438,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
7-2
Appearance and care
In order to maintain the appearance of your
vehicle, it is important to take proper care
of it.
To protect the paint surface, wash your
vehicle as soon as you can:
.
after a rainfall to prevent possible
damage from acid rain
.
after driving on coastal roads
.
when contaminants such as soot, bird
droppings, tree sap, metal particles or
bugs get on the paint surface
.
when dust or mud builds up on the
surface
Whenever possible, store or park your
vehicle inside a garage or in a covered
area.
When it is necessary to park outside, park
in a shady area or protect the vehicle with a
body cover.
Be careful not to scratch the paint surface
when putting on or removing the body
cover.
WASHING
Wash dirt off the vehicle with a wet sponge
and plenty of water. Clean the vehicle
thoroughly using a mild soap, a special
vehicle soap or general purpose dishwash-
ing liquid mixed with clean, lukewarm
(never hot) water.
CAUTION
.
Do not use car washes that use acid in
the detergent. Some car washes, espe-
cially brushless ones, use some acid for
cleaning. The acid may react with some
plastic vehicle components, causing
them to crack. This could affect their
appearance, and also could cause them
not to function properly. Always check
with your car wash to confirm that acid is
not used.
.
Do not wash the vehicle with strong
household soap, strong chemical deter-
gents, gasoline or solvents.
.
Do not wash the vehicle in direct sun-
light or while the vehicle body is hot, as
the surface may become water-spotted.
.
Avoid using tight-napped or rough
cloths, such as washing mitts. Care must
be taken when removing caked-on dirt or
other foreign substances so the paint
surface is not scratched or damaged.
Rinse the vehicle again with plenty of clean
water.
Inside flanges, seams and folds on the
doors, hatches and hood are particularly
vulnerable to the effects of road salt.
Therefore, these areas must be regularly
cleaned. Make sure that the drain holes in
the lower edge of the door are open. Spray
water under the body and in the wheel
wells to loosen the dirt and wash away
road salt.
Avoid leaving water spots on the paint
surface by using a damp chamois to dry the
vehicle.
WAXING
Regular waxing protects the paint surface
and helps retain new vehicle appearance.
Polishing is recommended to remove built-
up wax residue and to avoid a weathered
appearance before reapplying wax.
An INFINITI retailer can assist you in
choosing the proper product.
.
Wax your vehicle only after a thorough
CLEANING EXTERIOR
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(439,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
washing. Follow the instructions sup-
plied with the wax.
.
Do not use a wax containing any
abrasives, cutting compounds or clea-
ners that may damage the vehicle
finish.
Machine compound or aggressive polish-
ing on a base coat/clear coat paint finish
may dull the finish or leave swirl marks.
REMOVING SPOTS
Remove tar and oil spots, industrial dust,
insects, and tree sap as quickly as possible
from the paint surface to avoid lasting
damage or staining. Special cleaning
products are available at an INFINITI
retailer or any automotive accessory
stores.
UNDERBODY
In areas where road salt is used in winter,
the underbody must be cleaned regularly.
This will prevent dirt and salt from building
up and causing the acceleration of corro-
sion on the underbody and suspension.
Before the winter period and again in the
spring, the underseal must be checked
and, if necessary, re-treated.
GLASS
Use glass cleaner to remove smoke and
dust film from the glass surfaces. It is
normal for glass to become coated with a
film after the vehicle is parked in the hot
sun. Glass cleaner and a soft cloth will
easily remove this film.
CAUTION
When cleaning the inside of the windows,
do not use sharp-edged tools, abrasive
cleaners or chlorine-based disinfectant clea-
ners. They could damage the electrical
conductors, radio antenna elements or rear
window defroster elements.
WHEELS
Wash the wheels when washing the vehicle
to maintain their appearance.
.
Clean the inner side of the wheels when
the wheel is changed or the underside
of the vehicle is washed.
.
Inspect wheel rims regularly for dents
or corrosion. Such damage may cause
loss of pressure or poor seal at the tire
bead.
.
INFINITI recommends that the road
wheels be waxed to protect against
road salt in areas where it is used
during winter.
CAUTION
Do not use abrasive cleaners when washing
the wheels.
Aluminum alloy wheels
Wash regularly with a sponge dampened in
a mild soap solution, especially during
winter months in areas where road salt is
used. Salt could discolor the wheels if not
removed.
CAUTION
Follow the directions below to avoid stain-
ing or discoloring the wheels:
.
Do not use a cleaner that uses strong
acid or alkali contents to clean the
wheels.
.
Do not apply wheel cleaners to the
wheels when they are hot. The wheel
temperature should be the same as
Appearance and care
7-3
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(440,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
7-4
Appearance and care
ambient temperature.
.
Rinse the wheel to completely remove
the cleaner within 15 minutes after the
cleaner is applied.
CHROME PARTS
Clean chrome parts regularly with a non-
abrasive chrome polish to maintain the
finish.
TIRE DRESSING
INFINITI does not recommend the use of
tire dressings. Tire manufacturers apply a
coating to the tires to help reduce dis-
coloration of the rubber. If a tire dressing is
applied to the tires, it may react with the
coating and form a compound. This com-
pound may come off the tire while driving
and stain the vehicle paint.
If you choose to use a tire dressing, take
the following precautions:
.
Use a water-based tire dressing. The
coating on the tire dissolves more
easily with an oil-based tire dressing.
.
Apply a light coat of tire dressing to
help prevent it from entering the tire
tread/grooves (where it would be diffi-
cult to remove).
.
Wipe off excess tire dressing using a dry
towel. Make sure the tire dressing is
completely removed from the tire
tread/grooves.
.
Allow the tire dressing to dry as
recommended by tire dressing manu-
facturer.
Occasionally remove loose dust from the
interior trim, plastic parts and seats using
a vacuum cleaner or soft bristled brush.
Wipe the vinyl and leather surfaces with a
clean, soft cloth dampened in mild soap
solution, then wipe clean with a dry soft
cloth.
Regular care and cleaning is required in
order to maintain the appearance of the
leather.
Before using any fabric protector, read the
manufacturer’s recommendations. Some
fabric protectors contain chemicals that
may stain or bleach the seat material.
Use a cloth dampened only with water, to
clean the meter and gauge lens.
WARNING
Do not use water or acidic cleaners (hot
steam cleaners) on the seat. This can
damage the seat or occupant classification
sensors. This can also affect the operation of
the air bag system and result in serious
personal injury.
CLEANING INTERIOR
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(441,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
CAUTION
.
Never use benzine, thinner, or any
similar material.
.
For cleaning, use a soft cloth, dampened
with water. Never use a rough cloth,
alcohol, benzine, thinner or any kind of
solvent or paper towel with a chemical
cleaning agent. They will scratch or
cause discoloration to the lens.
.
Do not spray any liquid such as water on
the meter lens. Spraying liquid may
cause the system to malfunction.
.
Small dirt particles can be abrasive and
damaging to the leather surfaces and
should be removed promptly. Do not use
saddle soap, car waxes, polishes, oils,
cleaning fluids, solvents, detergents or
ammonia-based cleaners as they may
damage the leather’s natural finish.
.
Only use fabric protectors approved by
INFINITI.
.
Do not use glass or plastic cleaner on
meter or gauge lens covers. It may
damage the lens cover.
AIR FRESHENERS
Most air fresheners use a solvent that
could affect the vehicle interior. If you use
an air freshener, take the following pre-
cautions:
.
Hanging-type air fresheners can cause
permanent discoloration when they
contact vehicle interior surfaces. Place
the air freshener in a location that
allows it to hang free and not contact
an interior surface.
.
Liquid-type air fresheners typically clip
on the ventilators. These products can
cause immediate damage and disco-
loration when spilled on interior sur-
faces.
Carefully read and follow the manufac-
turer’s instructions before using air fresh-
eners.
FLOOR MATS
WARNING
To avoid potential pedal interference that
may result in a collision, injury or death:
.
NEVER place a floor mat on top of
another floor mat in the driver front
position or install them upside down or
backwards.
.
It is recommended that you use only
genuine INFINITI floor mats specifically
designed for use in your vehicle model
and model year.
.
Properly position the mats in the floor-
well using the floor mat positioning
hook. See “Floor mat installation” (P.7-
6).
.
Make sure the floor mat does not
interfere with pedal operation.
.
Periodically check the floor mats to make
sure they are properly installed.
.
After cleaning the vehicle interior, check
the floor mats to make sure they are
properly installed.
The use of genuine INFINITI floor mats can
extend the life of your vehicle carpet and
make it easier to clean the interior. Mats
should be maintained with regular clean-
ing and replaced if they become exces-
sively worn.
Appearance and care
7-5
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
(442,1)
Model: 2017MY INFINITI QX70(S51) OM17E00S51U0 ]
7-6
Appearance and care
SAI0039
Floor mat installation
Your vehicle is equipped with floor mat
positioning hook(s). The number and
shape of the floor mat positioning hook(s)
for each seating position varies depending
on the vehicle.
When installing genuine INFINITI floor
mats, follow the installation instructions
provided with the mat and the following:
1. Position the floor mat in the floorwell so
that the floor mat grommet holes are
aligned with the hook(s).
2. Secure the grommet holes into the
hook(s) and ensure that the floor mat
is properly positioned.
3. Make sure the floor mat does not
interfere with pedal operation. With
the ignition in the OFF position and
the shift lever in the P (Park) position,
fully apply and release all pedals. The
floor mat must not interfere with pedal
operation or prevent the pedal from
returning to its normal position.
See an INFINITI retailer for details about
installing the floor mats in your vehicle.
SAI0055
Positioning hooks
The illustration shows the location of the
floor mat positioning hooks.
SEAT BELTS
The seat belts can be cleaned by wiping
them with a sponge dampened in a mild
soap solution. Allow the belts to dry
completely before using them.
See “Seat belts” (P.1-12).
WARNING
Do not allow wet seat belts to roll up in the
retractor. NEVER use bleach, dye, or chemi-
Condition:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст