Infiniti QX4 (R50). Manual — part 517
Tool number
(Kent-Moore No.)
Tool name
Description
(J25269-18)
Side bearing discs
(2 Req’d)
NT135
Selecting pinion height adjusting washer
KV381052S0
(
—
)
Rear axle shaft dummy
1 KV38105210
(
—
)
Torque wrench side
2 KV38105220
(
—
)
Vice side
NT142
Checking differential torque on limited slip differen-
tial
KV38100500
(J25273)
Gear carrier front oil
seal drift
NT115
Installing front oil seal
a: 85 mm (3.35 in) dia.
b: 60 mm (2.36 in) dia.
Noise, Vibration and Harshness (NVH)
Troubleshooting
NBPD0051
Refer to “NVH TROUBLESHOOTING CHART”, PD-3.
SPD479A
On-vehicle Service
FRONT OIL SEAL REPLACEMENT
NBPD0030
1.
Remove propeller shaft.
2.
Loosen drive pinion nut.
Tool number: KV38108300 (J44195)
SPD737
3.
Remove companion flange.
REAR FINAL DRIVE
H233B
Preparation (Cont’d)
PD-40
SPD738
4.
Remove front oil seal.
SPD739
5.
Apply multi-purpose grease to cavity at sealing lips of oil seal.
Press front oil seal into carrier.
Tool number:
KV38100500 (J25273)
6.
Install companion flange and drive pinion nut.
7.
Install rear propeller shaft.
GI
MA
EM
LC
EC
FE
AT
TF
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REAR FINAL DRIVE
H233B
On-vehicle Service (Cont’d)
PD-41
Components
NBPD0031
SPD362AA
REAR FINAL DRIVE
H233B
Components
PD-42
Removal and Installation
NBPD0032
REMOVAL
NBPD0032S01
I
Remove rear of propeller shaft.
Plug front end of transfer.
I
Remove axle shaft.
Refer to AX-19, “Removal”.
I
Remove rear final drive mounting bolts.
CAUTION:
Be careful not to damage spline, sleeve yoke and front oil seal
when removing propeller shaft.
SPD123
INSTALLATION
NBPD0032S02
I
Fill final drive with recommended gear oil.
SPD767
I
Pay attention to the direction of gasket.
SPD149
Disassembly
NBPD0033
PRE-INSPECTION
NBPD0033S01
Before disassembling final drive, perform the following inspection.
I
Total preload
a)
Turn drive pinion in both directions several times to seat bear-
ing rollers correctly.
b)
Check total preload with Tool.
Tool number: ST3127S000 (J25765-A)
Total preload:
1.2 - 2.0 N·m (12 - 20 kg-cm, 10 - 17 in-lb)
SPD246
I
Ring gear to drive pinion backlash
Check backlash of ring gear with a dial indicator at several
points.
Ring gear-to-drive pinion backlash:
0.13 - 0.18 mm (0.0051 - 0.0071 in)
GI
MA
EM
LC
EC
FE
AT
TF
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
REAR FINAL DRIVE
H233B
Removal and Installation
PD-43
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст