Infiniti QX4 (R50). Manual — part 386
MEL870L
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
INFINITI COMMUNICATOR (IVCS)
Wiring Diagram — IVCS — (Cont’d)
EL-361
MEL871L
INFINITI COMMUNICATOR (IVCS)
Wiring Diagram — IVCS — (Cont’d)
EL-362
SEL331X
CONSULT-II
NBEL0183
CONSULT-II INSPECTION PROCEDURE
NBEL0183S01
1.
Turn ignition switch “OFF”.
2.
Insert UEN99A program card in to CONSULT-II.
3.
Connect CONSULT-II to the data link connector.
SEL762W
4.
Turn ignition switch “ON”.
5.
Touch “START”.
SEL763W
6.
Touch “IVCS”.
SEL763W
7.
Perform each diagnostic item according to the item application
chart as follows:
8.
When CONSULT-II inspection is terminated, follow the proce-
dure shown below.
a.
Touch “BACK” key of CONSULT-II until “SELECT SYSTEM”
appears, then turn off CONSULT-II.
b.
Turn ignition switch to OFF position.
c.
Disconnect CONSULT-II DDL connector.
NOTE:
If the DDL connector is disconnected before turning ignition
switch to “OFF” position, INFINITI communicator may not
operate properly.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
BT
HA
SC
IDX
INFINITI COMMUNICATOR (IVCS)
CONSULT-II
EL-363
APPLICATION ITEMS
NBEL0183S02
Mode
Description
Reference
page
SELF DIAG RESULTS
Displays the result of self-diagnosis.
DATA MONITOR
Two modes, “GPS MONITOR” and “SWITCH MONITOR” can be selected in this
mode.
I
Displays current data related to GPS in “GPS MONITOR” mode.
I
Displays IVCS switch and outside door handle switch condition in “SWITCH
MONITOR” mode.
FUNCTION CHECK
In this mode, “Remote door unlock function” can be checked using CONSULT-II.
Door can be unlocked according to the commands to the smart entrance control
unit by the IVCS unit. This check verifies communication circuit between smart
entrance control unit and IVCS unit.
REGISTERED DATA
Displays the following data registered in the IVCS unit. In this mode the data can-
not be re-written.
I
Unit ID
I
Cellular phone number
I
VIN (Vehicle Identification Number)
CONFIGURATION
(See Note.)
In this mode, the system can be set up in the demonstration mode to confirm sys-
tem operation.
Various data related to both the Communicator Response Center contract and cel-
lular provider can be written/updated in this mode.
I
Phone number
I
NAM (Number Assignment Module)
I
Stolen vehicle tracking setting (Default should always be on.)
I
Alarm notification setting (Default should always be on.)
ECU PART NUMBER
Displays the part number of the IVCS unit.
—
NOTE:
Data must not be rewritten without prior approval from the
customer.
SEL440W
“SELF-DIAG RESULTS” MODE
NBEL0183S03
How to Perform Self-diagnosis
NBEL0183S0301
1.
Touch “SELF-DIAG RESULTS”.
2.
Touch “START”.
SEL441W
3.
If no malfunction is detected, CONSULT-II will show “NO DTC”.
INFINITI COMMUNICATOR (IVCS)
CONSULT-II (Cont’d)
EL-364
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст