Infiniti QX4 (R50). Manual — part 576
Diagnostic Procedure
NBTF0021
1
CHECK 2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Refer to “2-4WD Shift Solenoid Valve and Transfer Fluid Temperature Sensor”, “COMPONENT INSPECTION”, TF-111.
SMT778D
OK or NG
OK
©
GO TO 2.
NG
©
Check the following. If OK, repair or replace 2-4WD shift solenoid valve and 4WD
shift switch.
I
Continuity of transfer sub-harness
Refer to “TRANSFER TERMINAL CORD ASSEMBLY SUB-HARNESS CONNECTOR”,
“COMPONENT INSPECTION”, TF-114.
2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Diagnostic Procedure
TF-66
2
CHECK INPUT SIGNAL
With CONSULT-II
1. Select “ECU INPUT SIGNALS” in Data Monitor.
2. Read out ON/OFF status of “2WD SW” and “LOCK SWITCH”.
SMT974D
OK or NG
OK
©
1. Perform transfer control unit input/output signal inspection. Refer to “TRANSFER
CONTROL UNIT INSPECTION TABLE”, “TROUBLE DIAGNOSIS — GENERAL
DESCRIPTION”, TF-55.
2. If NG, recheck transfer control unit pin terminals for damage or loose connection with
harness connector.
NG
©
GO TO 3.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Diagnostic Procedure (Cont’d)
TF-67
3
CHECK 4WD SHIFT SWITCH POWER SOURCE
1. Disconnect 4WD shift switch harness connector.
2. Turn ignition switch to “ON” position.
3. Check voltage between 4WD shift switch harness connector terminal 1 and body ground.
Voltage: Battery voltage
SMT852D
OK or NG
OK
©
GO TO 4.
NG
©
Check the following.
I
No. 18 fuse (10A)
I
Continuity between ignition switch and 4WD shift switch
2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Diagnostic Procedure (Cont’d)
TF-68
4
CHECK HARNESS CONTINUITY
1. Turn ignition switch to “OFF” position.
2. Check continuity between the following terminals:
I
Transfer control unit 9 and 4WD shift switch 2 (2WD)
I
Transfer control unit 18 and 4WD shift switch 5 (4H)
I
Transfer control unit 24 and 4WD shift switch 3 (AUTO)
I
Transfer control unit 23 and 4WD shift switch 6 (4LO)
I
Transfer control unit 1 and Transfer terminal cord assembly sub-harness connector 4
I
4WD shift switch 4 and Transfer terminal cord assembly sub-harness connector 5
Continuity should exist.
SMT853D
OK or NG
OK
©
GO TO 5.
NG
©
Repair harness or connector.
5
PERFORM SELF-DIAGNOSIS AGAIN
After driving for a while, perform self-diagnosis again.
Refer to “Trouble Diagnosis without CONSULT-II”, TF-27.
OK or NG
OK
©
INSPECTION END
NG
©
1. Perform transfer control unit input/output signal inspection. Refer to “TRANSFER
CONTROL UNIT INSPECTION TABLE”, “TROUBLE DIAGNOSIS — GENERAL
DESCRIPTION”, TF-55.
2. If NG, recheck transfer control unit pin terminals for damage or loose connection with
harness connector.
GI
MA
EM
LC
EC
FE
AT
PD
AX
SU
BR
ST
RS
BT
HA
SC
EL
IDX
2-4WD SHIFT SOLENOID VALVE AND 4WD SHIFT SWITCH
Diagnostic Procedure (Cont’d)
TF-69
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст