Infiniti Q45. Manual — part 372
TROUBLE DIAGNOSIS
EC-127
C
D
E
F
G
H
I
J
K
L
M
A
EC
Generic Scan Tool (GST) Function
NBS001R9
DESCRIPTION
Generic Scan Tool (OBDII scan tool) complying with SAE J1978 has
8 different functions explained below.
ISO9141 is used as the protocol.
The name “GST” or “Generic Scan Tool” is used in this service man-
ual.
FUNCTION
PBIB0197E
SEF139P
Diagnostic test mode
Function
Service $01
READINESS TESTS
This diagnostic service gains access to current emission-related data values, including
analog inputs and outputs, digital inputs and outputs, and system status information.
Service $02
(FREEZE DATA)
This diagnostic service gains access to emission-related data value which were stored by
ECM during the freeze frame. For details, refer to
Service $03
DTCs
This diagnostic service gains access to emission-related power train trouble codes which
were stored by ECM.
EC-128
TROUBLE DIAGNOSIS
INSPECTION PROCEDURE
1.
Turn ignition switch OFF.
2.
Connect GST to data link connector, which is located under LH
dash panel near the hood opener handle.
3.
Turn ignition switch ON.
4.
Enter the program according to instruction on the screen or in
the operation manual.
(*: Regarding GST screens in this section, sample screens are
shown.)
Service $04
CLEAR DIAG INFO
This diagnostic service can clear all emission-related diagnostic information. This
includes:
●
Clear number of diagnostic trouble codes (Service $01)
●
Clear diagnostic trouble codes (Service $03)
●
Clear trouble code for freeze frame data (Service $01)
●
Clear freeze frame data (Service $02)
●
Reset status of system monitoring test (Service $01)
●
Clear on board monitoring test results (Service $06 and $07)
Service $06
(ON BOARD TESTS)
This diagnostic service accesses the results of on board diagnostic monitoring tests of
specific components/systems that are not continuously monitored.
Service $07
(ON BOARD TESTS)
This diagnostic service enables the off board test drive to obtain test results for emission-
related powertrain components/systems that are continuously monitored during normal
driving conditions.
Service $08
—
This diagnostic service can close EVAP system in ignition switch ON position (Engine
stopped). When this diagnostic service is performed, the following parts can be opened or
closed.
●
EVAP canister vent control valve: closed
●
Vacuum cut valve bypass valve: open
In the following conditions, this diagnostic service cannot function.
●
Low ambient temperature
●
Low battery voltage
●
Engine running
●
Ignition switch OFF
●
Low fuel temperature
●
Too much pressure is applied to EVAP system
Service $09
(CALIBRATION ID)
This diagnostic service enables the off-board test device to request specific vehicle infor-
mation such as Vehicle Identification Number (VIN) and Calibration IDs.
Diagnostic test mode
Function
PBIB0196E
SEF398S
TROUBLE DIAGNOSIS
EC-129
C
D
E
F
G
H
I
J
K
L
M
A
EC
5.
Perform each diagnostic service according to each service pro-
cedure.
For further information, see the GST Operation Manual of the
tool maker.
CONSULT-II Reference Value in Data Monitor Mode
NBS001RA
Remarks:
●
Specification data are reference values.
●
Specification data are output/input values which are detected or supplied by the ECM at the connector.
* Specification data may not be directly related to their components signals/values/operations.
i.e. Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show the specification data in
spite of the ignition timing not being adjusted to the specification data. This IGN TIMING monitors the data calculated by the ECM
according to the signals input from the camshaft position sensor and other ignition timing related sensors.
SEF416S
MONITOR ITEM
CONDITION
SPECIFICATION
ENG SPEED
●
Run engine and compare CONSULT-II value with the tachometer indication.
Almost the same speed as
the tachometer indication.
MAS A/F SE-B1
See
EC-135, "TROUBLE DIAGNOSIS - SPECIFICATION VALUE"
.
B/FUEL SCHDL
See
EC-135, "TROUBLE DIAGNOSIS - SPECIFICATION VALUE"
.
A/F ALPHA-B1
A/F ALPHA-B2
See
EC-135, "TROUBLE DIAGNOSIS - SPECIFICATION VALUE"
.
COOLAN TEMP/S
●
Engine: After warming up
More than 70
°
C (158
°
F)
A/F SEN1 (B1)
A/F SEN1 (B2)
●
Engine: After warming up
Maintaining engine speed at 2,000 rpm
Fluctuates around 1.5 V
HO2S2 (B1)
HO2S2 (B2)
●
Revving engine from idle to 3,000 rpm quickly after the following conditions
are met.
–
Engine: After warming up
–
Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
0 - 0.3V
←→
Approx. 0.6 -
1.0V
HO2S2 MNTR (B1)
HO2S2 MNTR (B2)
●
Revving engine from idle to 3,000 rpm quickly after the following conditions
are met.
–
Engine: After warming up
–
Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load
LEAN
←→
RICH
VHCL SPEED SE
●
Turn drive wheels and compare CONSULT-II value with the speedometer indi-
cation.
Almost the same speed as
speedometer indication
BATTERY VOLT
●
Ignition switch: ON (Engine stopped)
11 - 14V
ACCEL SEN 1
●
Ignition switch: ON
(engine stopped)
Accelerator pedal: Fully released
0.5 - 1.0V
Accelerator pedal: Fully depressed
4.0 - 4.8V
ACCEL SEN 2*
●
Ignition switch: ON
(engine stopped)
Accelerator pedal: Fully released
0.3 - 1.2V
Accelerator pedal: Fully depressed
3.9 - 4.8V
THRTL SEN 1
THRTL SEN 2*
●
Ignition switch: ON
(Engine stopped)
●
Selector lever: D
Accelerator pedal: Fully released
More than 0.36V
Accelerator pedal: Fully depressed
Less than 4.75V
EVAP SYS PRES
●
Ignition switch: ON
Approx. 1.8 - 4.8V
START SIGNAL
●
Ignition switch: ON
→
START
→
ON
OFF
→
ON
→
OFF
CLSD THL POS
●
Ignition switch: ON
(Engine stopped)
Accelerator pedal: Fully released
ON
Accelerator pedal: Slightly depressed
OFF
EC-130
TROUBLE DIAGNOSIS
AIR COND SIG
●
Engine: After warming up, idle the
engine
Air conditioner switch: OFF
OFF
Air conditioner switch: ON
(Compressor operates.)
ON
P/N POSI SW
●
Ignition switch: ON
Selector lever: P or N
ON
Selector lever: Except above
OFF
PW/ST SIGNAL
●
Engine: After warming up, idle the
engine
Steering wheel: Not being turned
(Forward direction)
OFF
Steering wheel: Being turned
ON
LOAD SIGNAL
●
Ignition switch: ON
Rear window defogger switch: ON
and/or
Lighting switch: 2nd position
ON
Rear window defogger switch and lighting
switch: OFF
OFF
IGNITION SW
●
Ignition switch: ON
→
OFF
→
ON
ON
→
OFF
→
ON
HEATER FAN SW
●
Engine: After warming up, idle the
engine
Heater fan switch: ON
ON
Heater fan switch: OFF
OFF
BRAKE SW
●
Ignition switch: ON
Brake pedal: Fully released
OFF
Brake pedal: Slightly depressed
ON
INJ PULSE-B1
INJ PULSE-B2
●
Engine: After warming up
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Idle
2.0 - 3.0 msec
2,000 rpm
1.9 - 2.9 msec
IGN TIMING
●
Engine: After warming up
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Idle
7
°
- 17
°
BTDC
2,000 rpm
25
°
- 45
°
BTDC
CAL/LD VALUE
●
Engine: After warming up
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Idle
15% - 35%
2,500 rpm
10% - 35%
MASS AIRFLOW
●
Engine: After warming up
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Idle
3.8 - 5.2 g·m/s
2,500 rpm
16.0 - 21.5 g·m/s
PURG VOL C/V
●
Engine: After warming up
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Idle
0%
2,000 rpm
—
INT/V TIM (B1)
INT/V TIM (B2)
●
Engine: After warming up
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Idle
−
5
°
- 5
°
CA
2,000 rpm
Approx. 0
°
- 20
°
CA
INT/V SOL (B1)
INT/V SOL (B2)
●
Engine: After warming up
●
Selector lever: P or N
●
Air conditioner switch: OFF
●
No load
Idle
0% - 2%
2,000 rpm
Approx. 25% - 50%
MONITOR ITEM
CONDITION
SPECIFICATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст