Infiniti Q45. Manual — part 21
ELECTRICAL COMPONENT INSPECTION
ACS-77
[ICC]
C
D
E
F
G
H
I
J
L
M
A
B
ACS
ELECTRICAL COMPONENT INSPECTION
PFP:00000
ICC Steering Switch
NKS001LB
1.
Remove ICC steering switch.
2.
Check resistance between ICC steering switch terminals by
pressing each switch.
Booster Solenoid
NKS001LD
Disconnect brake booster connector, and check resistance between
terminals.
Release Switch
NKS001LE
Disconnect brake booster connector and check resistance between
terminals.
(Note): However, if pedal is depressed insufficiently, resistance value may remain
unchanged.
Terminals
Switch
Condition
Resistance [k
Ω
]
1
2
MAIN
Pressed
Approx. 0
Released
Approx. 5.5
DISTANCE
Pressed
Approx. 0.7
Released
Approx. 5.5
RESUME/ACCELERATE
Pressed
Approx. 2.6
Released
Approx. 5.5
SET/COAST
Pressed
Approx. 1.4
Released
Approx. 5.5
CANCEL
Pressed
Approx. 0.3
Released
Approx. 5.5
PKIA2215E
Terminals
Resistance [
Ω
]
4
6
Approx. 1.4
PKIC5181E
Condition
1 - 3
1 - 2
2 - 3
Release the brake pedal.
Continuity
should exist.
Continuity
should not
exist.
Continuity
should not
exist.
Depress the brake pedal.
Continuity
should not
exist. (Note)
Continuity
should exist.
(Note)
Continuity
should not
exist.
SKIA1256E
ACS-78
[ICC]
ELECTRICAL COMPONENT INSPECTION
ICC Brake Switch and Stop Lamp Switch
NKS001LC
Check each switch after adjusting brake pedal, refer to
ICC BRAKE HOLD RELAY
NKS002KK
Disconnect ICC brake hold relay, and check resistance between ter-
minals.
Condition
Continuity
ICC brake switch
Stop lamp switch
When brake pedal is depressed
No
Yes
When brake pedal is released
Yes
No
PKIA9910E
Terminals
Condition
Continuity
3
4
Applying battery voltage to
between terminals 1 and 2.
No
6
7
Yes
3
4
No battery voltage
Yes
6
7
No
PKIC4924E
REMOVAL AND INSTALLATION
ACS-79
[ICC]
C
D
E
F
G
H
I
J
L
M
A
B
ACS
REMOVAL AND INSTALLATION
PFP:00000
ICC Unit
NKS001LF
REMOVAL
1.
Remove the trunk side finisher (right). Refer to
EI-60, "TRUNK ROOM TRIM & TRUNK LID FINISHER"
2.
Disconnect ICC unit connector.
3.
Remove mounting bolts from ICC unit assembly.
INSTALLATION
Installation is the reverse order of removal.
ICC Sensor
NKS001LG
REMOVAL
1.
Remove the front bumper. Refer to
2.
Disconnect ICC sensor connector.
3.
Remove mounting bolts and a nut from ICC sensor.
PKIA9677E
1.
ICC sensor
PKIC4907E
ACS-80
[ICC]
REMOVAL AND INSTALLATION
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Adjust the laser beam aiming every time the ICC sensor is removed or installed.
ICC Warning Chime (Without LDW models)
NKS001LH
REMOVAL
1.
Remove instrument lower driver panel. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
2.
Disconnect ICC warning chime connector.
3.
Remove mounting bolt from ICC warning chime.
INSTALLATION
Installation is the reverse order of removal.
ICC Warning Chime (With LDW models)
NKS002KJ
REMOVAL AND INSTALLATION
Refer to
DI-100, "Removal and Installation for LDW Chime"
.
ICC Steering Switch
NKS001LI
REMOVAL AND INSTALLATION
Refer to
SRS-40, "DRIVER AIR BAG MODULE"
.
PKIA9826E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст