Infiniti Q45. Manual — part 890
TROUBLE DIAGNOSIS FOR SYSTEM
STC-63
[WITH REAR ACTIVE STEER]
C
D
E
F
H
I
J
K
L
M
A
B
STC
2.
CHECK POWER SUPPLY SIGNAL
With CONSULT-II
1.
Start engine.
2.
Select “DATA MONITOR” mode for “RAS/HICAS” with CONSULT-II.
3.
Read out the value of “C/U VOLTAGE”, “MOTOR VOLTAGE”
and “HICAS RELAY”.
OK or NG
OK >> GO
TO
7.
NG
>> GO TO 3.
Monitored item
Condition
Display value
C/U VOLTAGE
Ignition switch: ON
Battery voltage
MOTOR VOLTAGE
Ignition switch: ON
Battery voltage
Ignition switch: OFF
0 V
HICAS RELAY
Ignition switch: ON
ON
Ignition switch: OFF
OFF
SGIA1477E
STC-64
[WITH REAR ACTIVE STEER]
TROUBLE DIAGNOSIS FOR SYSTEM
3.
CHECK POWER SUPPLY
1.
Turn ignition switch “OFF”.
2.
Disconnect RAS control unit harness connector.
3.
Check voltage between RAS control unit harness connector (A)
terminals and ground.
4.
Turn ignition switch “ON”. (Do not start engine.)
5.
Check voltage between RAS control unit harness connector (A)
terminals and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Check the following. If any items are damaged, repair or
replace damaged parts.
●
10 A fuse [No. 7 located in the fuse block (J/B) No.1]. Refer to
.
●
20 A fuse [No. 76 located in the fuse, fusible link and relay box]. Refer to
●
Harness for short or open between ignition switch and RAS control unit harness connector B39
terminals 27.
●
Harness for short or open between battery and RAS control unit harness connector B39 termi-
nals 37.
●
Harness for short or open between RAS control unit harness connector B39 terminal 25 and
RAS motor relay harness connector B42 terminal 1.
●
Harness for open circuit or short to power between RAS motor relay harness connector B42
terminal 2 and ground.
●
Connector
Terminal
Voltage (Approx.)
B39
25 - Ground
0 V
27 - Ground
37 - Ground
SGIA1464E
Connector
Terminal
Voltage (Approx.)
B39
25 - Ground
Battery voltage
27 - Ground
37 - Ground
SGIA1465E
TROUBLE DIAGNOSIS FOR SYSTEM
STC-65
[WITH REAR ACTIVE STEER]
C
D
E
F
H
I
J
K
L
M
A
B
STC
4.
CHECK GROUND CIRCUIT
1.
Turn ignition switch “OFF”.
2.
Disconnect RAS control unit harness connector.
3.
Check continuity between RAS control unit harness connector
(A) B39 terminal 40 and ground.
Also check harness for short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Check the following. If any items are damaged, repair or
replace damaged parts.
●
Harness open circuit or short to power between noise
suppressor harness connector B41 terminal 4 and
RAS control unit harness connector B39 terminal 40.
●
Harness open circuit or short to power between noise suppressor harness connector B40 termi-
nal 2 and ground.
5.
CHECK RAS MOTOR RELAY
1.
Turn ignition switch “OFF”.
2.
Remove RAS motor relay. Refer to
STC-41, "Component Parts Location"
3.
Apply 12 V direct current between RAS motor relay connector
B42 terminals 1 and 2.
4.
Check continuity between RAS motor relay connector B42 ter-
minals 3 and 5.
5.
Check continuity between RAS motor relay connector B42 ter-
minals 1 and 2.
OK or NG
OK
>> GO TO 6.
NG
>> Replace RAS motor relay.
6.
CHECK NOISE SUPPRESSOR
1.
Turn ignition switch “OFF”.
2.
Remove noise suppressor. Refer to
STC-41, "Component Parts Location"
3.
Check noise suppressor connector (A) continuity between the
following terminals.
OK or NG
OK
>> GO TO 7.
NG
>> Replace RAS motor relay.
Continuity should exist.
SGIA1466E
Terminal
Condition
Continuity
3 - 5
1 2 V direct current supply between terminals 1 and 2
Yes
OFF
No
1 – 2
: 74
Ω
SGIA1286E
1 – 3
: Continuity should exist.
1 – 2
: Continuity should no exist.
1 – 4
: Continuity should no exist.
2 – 1
: Continuity should no exist.
2 – 3
: Continuity should no exist.
2 – 4
: Continuity should exist.
SGIA1467E
STC-66
[WITH REAR ACTIVE STEER]
TROUBLE DIAGNOSIS FOR SYSTEM
7.
CHECK RAS CONTROL UNIT
Check RAS control unit input/output signal. Refer to
STC-47, "RAS Control Unit Input/Output Signal Refer-
.
OK or NG
OK
>> GO TO 8.
NG
>> Check RAS control unit pin terminals for damage or loose connection with harness connector. If
any items are damaged, repair or replace damaged parts.
8.
CHECK DTC
Perform the self-diagnosis, after driving a vehicle for a while.
OK or NG
OK
>> INSPECTION END
NG
>> Replace RAS control unit. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст