Infiniti Q45. Manual — part 130
TROUBLE DIAGNOSIS
ATC-115
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Sunload Sensor Circuit
NJS0008X
COMPONENT DESCRIPTION
Sunload Sensor
The sunload sensor is located on the left defroster grille. It detects
sunload entering through windshield by means of a photo diode. The
sensor converts the sunload into a current value which is then input
into the auto amp.
SUNLOAD INPUT PROCESS
The auto amp. also includes a processing circuit which averages the variations in detected sunload over a
period of time. This prevents drastic swings in the ATC system operation due to small or quick variations in
detected sunload.
For example, consider driving along a road bordered by an occasional group of large trees. The sunload
detected by the sunload sensor will vary whenever the trees obstruct the sunlight. The processing circuit aver-
ages the detected sunload over a period of time, so that the (insignificant) effect of the trees momentarily
obstructing the sunlight does not cause any change in the ATC system operation. On the other hand, shortly
after entering a long tunnel, the system will recognize the change in sunload, and the system will react accord-
ingly.
DIAGNOSIS PROCEDURE FOR SUNLOAD SENSOR
SYMPTOM: Sunload sensor circuit is open or shorted. (25 or
−
25 is
indicated on auto amp. as a result of performing self-diagnosis
STEP-2.)
1.
CHECK VOLTAGE BETWEEN SUNLOAD SENSOR AND GROUND
1.
Disconnect sunload sensor connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunload sensor harness connector M44
terminal 1 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 4.
RJIA0109E
RJIA0926E
1 – Ground
: Approx. 5 V
RJIA2027E
ATC-116
TROUBLE DIAGNOSIS
2.
CHECK CIRCUIT CONTINUITY BETWEEN SUNLOAD SENSOR AND AUTO AMP.
1.
Turn ignition switch OFF.
2.
Disconnect auto amp. connector.
3.
Check continuity between sunload sensor harness connector
M44 terminal 2 and auto amp. harness connector M119 terminal
11.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK SUNLOAD SENSOR.
1.
Reconnect sunload sensor connector and auto amp. connector.
2.
Refer to
OK or NG
OK
>> 1. Replace auto amp.
2. Go to self-diagnosis
ATC-54, "FUNCTION CONFIRMATION PROCEDURE"
and perform self-
diagnosis STEP-2. Confirm that code No. 20 is displayed.
NG
>> 1. Replace sunload sensor.
2. Go to self-diagnosis
ATC-54, "FUNCTION CONFIRMATION PROCEDURE"
and perform self-
diagnosis STEP-2. Confirm that code No. 20 is displayed.
4.
CHECK CIRCUIT CONTINUITY BETWEEN SUNLOAD SENSOR AND AUTO AMP.
1.
Turn ignition switch OFF.
2.
Disconnect auto amp. connector.
3.
Check continuity between sunload sensor harness connector
M44 terminal 1 and auto amp. harness connector M119 terminal
12.
4.
Check continuity between auto amp. harness connector M119
terminal 12 and ground.
OK or NG
OK
>> 1. Replace auto amp.
2. Go to self-diagnosis
ATC-54, "FUNCTION CONFIRMATION PROCEDURE"
and perform self-
diagnosis STEP-2. Confirm that code No. 20 is displayed.
NG
>> Repair harness or connector.
2 – 11
: Continuity should exist.
RJIA3064E
1 – 12
: Continuity should exist.
12 – Ground
: Continuity should not exist.
RJIA3065E
TROUBLE DIAGNOSIS
ATC-117
C
D
E
F
G
H
I
K
L
M
A
B
ATC
COMPONENT INSPECTION
Sunload Sensor
Measure voltage between auto amp. harness connector M119 termi-
nal 12 and ground.
●
When checking sunload sensor, select a place where sun shines directly on it.
If NG, replace sunload sensor.
RJIA0257E
SHA930E
ATC-118
TROUBLE DIAGNOSIS
Intake Sensor Circuit
NJS0008Y
COMPONENT DESCRIPTION
Intake Sensor
The intake sensor is located on the heater & cooling unit. It converts
temperature of air after it passes through the evaporator into a resis-
tance value which is then input to the auto amp.
DIAGNOSIS PROCEDURE FOR INTAKE SENSOR
SYMPTOM: Intake sensor circuit is open or shorted. (24 or
−
24 is
indicated on auto amp. as a result of performing self-diagnosis
STEP-2.)
1.
CHECK VOLTAGE BETWEEN INTAKE SENSOR AND GROUND
1.
Disconnect intake sensor connector.
2.
Turn ignition switch ON.
3.
Check voltage between intake sensor harness connector M90
terminal 32 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 4.
2.
CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND AUTO AMP.
1.
Turn ignition switch OFF.
2.
Disconnect auto amp. connector.
3.
Check continuity between intake sensor harness connector M90
terminal 36 and auto amp. harness connector M119 terminal 11.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
RJIA0110E
RHA056GA
32 – Ground
: Approx. 5 V
RJIA3067E
36 – 11
: Continuity should exist.
RJIA3068E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст