Infiniti Q45. Manual — part 67
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-181
D
E
F
G
H
I
J
K
L
M
A
B
AT
TCWM0482E
AT-182
TROUBLE DIAGNOSIS FOR SYMPTOMS
TCWM0483E
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-183
D
E
F
G
H
I
J
K
L
M
A
B
AT
TCM terminals and data are reference value. Measured between each terminal and ground.
A/T CHECK Indicator Lamp Does Not Come On
NCS0010E
SYMPTOM:
A/T CHECK indicator lamp does not come on for about 2 seconds when turning ignition switch to ON.
DIAGNOSTIC PROCEDURE
1.
CHECK CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
Is a malfunction in the CAN communication indicated in the results?
YES
>> Check CAN communication line. Refer to
AT-99, "DTC U1000 CAN COMMUNICATION LINE"
.
NO
>> GO TO 2.
2.
CHECK A/T CHECK INDICATOR LAMP CIRCUIT
Check the combination meters. Refer to
OK or NG
OK
>> GO TO 3
NG
>> Repair or replace damaged parts.
3.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
AT-173, "MAIN POWER SUPPLY AND GROUND CIR-
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
Engine Cannot Be Started In “P” or “N” Position
NCS0010F
SYMPTOM:
●
Engine cannot be started with selector lever in “P” or “N” position.
●
Engine can be started with selector lever in “D”or “R” position.
DIAGNOSTIC PROCEDURE
1.
CHECK PNP SWITCH CIRCUIT
Perform self-diagnosis. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
Do the self-diagnostic results indicate PNP switch?
YES
>> Check the malfunctioning system. Refer to
AT-107, "DTC P0705 PARK/NEUTRAL POSITION
NO
>> GO TO 2.
Terminal
Wire
color
Item
Condition
Data (Approx.)
3
L
CAN-H
–
–
4
PU
K-line (CONSULT-
II signal)
The terminal is connected to the data link connector for CONSULT-II.
–
7
R
Back-up lamp
relay
Selector lever in “R” position.
0 V
Selector lever in other positions.
Battery voltage
8
P
CAN-L
–
–
AT-184
TROUBLE DIAGNOSIS FOR SYMPTOMS
2.
CHECK CONTROL LINKAGE
Check the control linkage. Refer to
AT-218, "Checking of A/T Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control linkage. Refer to
AT-218, "Adjustment of A/T Position"
3.
CHECK STARTING SYSTEM
Check starting system. Refer to
.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
In “P” Position, Vehicle Moves When Pushed
NCS0010G
SYMPTOM:
Even though the selector lever is set in “P” position, the parking mechanism is not actuated, allowing
the vehicle to be moved when it is pushed.
DIAGNOSTIC PROCEDURE
1.
CHECK PNP SWITCH CIRCUIT
Perform self-diagnosis. Refer to
AT-87, "SELF-DIAGNOSTIC RESULT MODE"
.
Do the self-diagnostic results indicate PNP switch?
YES
>> Check the malfunctioning system. Refer to
AT-107, "DTC P0705 PARK/NEUTRAL POSITION
NO
>> GO TO 2.
2.
CHECK CONTROL LINKAGE
Check the control linkage. Refer to
AT-218, "Checking of A/T Position"
OK or NG
OK
>> GO TO 3.
NG
>> Adjust control linkage. Refer to
AT-218, "Adjustment of A/T Position"
3.
CHECK PARKING COMPONENTS
Check parking components. Refer to
.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-225, "Control Valve with TCM and A/T Fluid Temperature Sensor 2"
2.
Check A/T fluid condition. Refer to
AT-51, "A/T Fluid Condition Check"
OK or NG
OK
>> INSPECTION END
NG
>> Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
(Symptom No.65).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст