Infiniti Q45. Manual — part 690
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-97
C
D
E
F
G
H
I
J
L
M
A
B
LT
TKWM1500E
LT-98
TURN SIGNAL AND HAZARD WARNING LAMPS
Symptom Chart
NKS00194
Symptom
Possible cause
Repair Procedure
Turn signal and hazard warning
lamps do not operate.
1. Combination flasher unit
2. Open in combination flasher unit
circuit
1. Check combination flasher unit. Refer to
2. Check wiring to combination flasher unit for open circuit.
Turn signal lamps do not oper-
ate but hazard warning lamps
operate.
1. 10A fuse
2. Combination flasher unit
3. Turn signal switch
4. Open in turn signal switch circuit
1. Check 10A fuse [No. 5, located in fuse block (J/B) No.1].
Turn ignition switch ON and verify battery positive voltage
is present at terminal 1 of combination flasher unit.
2. Check combination flasher unit. Refer to
3. Check turn signal switch. Refer to
4. Check harness between combination flasher unit terminal 2
and turn signal switch terminal 1 for open circuit.
Hazard warning lamps do not
operate but turn signal lamps
operate.
1. 15A fuse
2. Combination flasher unit
3. Hazard switch
4. Open in hazard switch circuit
5. Grounds M24 and M114
1. Check 15A fuse [No. 22, located in fuse block (J/B) No.1].
Verify battery positive voltage is present at terminal 4 of
combination flasher unit.
2. Check combination flasher unit. Refer to
3. Check hazard switch.
4. Check harness between combination flasher unit terminal 6
and hazard switch terminal 1 for open circuit.
5. Check grounds M24 and M114.
Front turn signal lamp LH or RH
does not operate.
1. Bulb
2. Grounds E24, E42 and E62
3. Open in front turn signal lamp cir-
cuit
1. Check bulb.
2. Check grounds E24, E42 and E62.
3. Check harness between combination switch and front turn
signal lamp for open circuit.
Rear turn signal lamp LH or RH
does not operate.
1. Bulb
2. Grounds B17 and B57
3. Open in rear turn signal lamp cir-
cuit
1. Check bulb.
2. Check grounds B17 and B57.
3. Check harness between combination switch and rear turn
signal lamp for open circuit.
LH and RH turn indicators do
not operate.
1. Grounds M24 and M114
1. Check grounds M24 and M114.
LH or RH turn indicator does not
operate.
1. Bulb
2. Open in turn indicator circuit
1. Check bulb in combination meter.
2. Check harness between combination flasher unit and com-
bination meter (turn indicator) for open circuit.
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-99
C
D
E
F
G
H
I
J
L
M
A
B
LT
Electrical Components Inspection
NKS00195
COMBINATION FLASHER UNIT CHECK
●
Before checking, ensure that bulbs meet specifications.
●
Connect a battery and test lamp to the combination flasher unit,
as shown. Combination flasher unit is properly functioning if it
flashes when power is supplied to the circuit.
Bulb Replacement
NKS00196
FRONT TURN SIGNAL LAMP
Refer to
REAR TURN SIGNAL LAMP
Refer to
LT-115, "REAR COMBINATION LAMP"
Removal and Installation
NKS00197
FRONT TURN SIGNAL LAMP
Refer to
LT-33, "Removal and Installation"
SIDE TURN SIGNAL LAMP
Refer to
GW-117, "Disassembly and Assembly"
.
REAR TURN SIGNAL LAMP
Refer to
LT-116, "REAR COMBINATION LAMP"
PKIA5183E
LT-100
LIGHTING AND TURN SIGNAL SWITCH
LIGHTING AND TURN SIGNAL SWITCH
PFP:25540
Removal and Installation
NKS00198
1.
Remove steering column cover. Refer to
.
2.
Remove lighting and turn signal switch mounting screws and
remove lighting and turn signal switch from harness.
3.
Disconnect lighting and turn signal switch connector.
Switch Circuit Inspection
NKS00199
Using circuit tester, check continuity between the lighting and turn signal switch connector terminals in each
position of the switch.
Hi: “HIGH BEAM” position, Lo: “LOW BEAM” position, P: “FLASH TO PASS” position
PKIA2249E
PKIB1324E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст