Infiniti Q45. Manual — part 83
ON-VEHICLE SERVICE
AT-245
D
E
F
G
H
I
J
K
L
M
A
B
AT
16. Remove revolution sensor from transmission case.
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
●
Do not place in an area affected by magnetism.
INSTALLATION
CAUTION:
After completing installation, check A/T fluid leakage, A/T fluid level and A/T position. Refer to
AT-218, "Checking of A/T Position"
1.
Install revolution sensor in transmission case.
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
●
Do not place in an area affected by magnetism.
2.
Connect revolution sensor connector.
3.
Securely fasten revolution sensor harness with clip.
SCIA3997E
: 5.8 N·m (0.59 kg-m, 51 in-lb)
SCIA3997E
SCIA7518E
SCIA7525E
AT-246
ON-VEHICLE SERVICE
4.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-45, "Recommended Chemical Prod-
.) to output shaft & companion flange com-
plement as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from the transmission case and output shaft & companion
flange complement mounting surfaces.
5.
Install output shaft & companion flange complement in A/T
assembly.
CAUTION:
Insert the tip of parking rod between the parking actuator
support when assembling the output shaft companion
flange complement.
6.
Tighten output shaft & companion flange complement mounting
bolts (1) to specified torque.
: Bolt (10)
CAUTION:
Do not reuse self-sealing bolts (2).
7.
Install rear engine mounting insulator. Refer to
.
SCIA5212E
SCIA5688E
Output shaft & companion flange complement
mounting bolt:
: 52 N·m (5.3 Kg-m, 38 ft-lb)
Self-sealing bolt:
: 61 N·m (6.2 Kg-m, 45 ft-lb)
SCIA6943E
SCIA5686E
ON-VEHICLE SERVICE
AT-247
D
E
F
G
H
I
J
K
L
M
A
B
AT
8.
AT-249, "Removal and Installation"
.
9.
Install oil pan to transmission case.
a.
Install oil pan gasket to oil pan.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Completely remove all moisture, oil and old gasket, etc. from oil pan mounting surface.
b.
Install oil pan (with oil pan gasket) to transmission case.
CAUTION:
●
Install it so that drain plug comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
c.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
CAUTION:
Do not reuse oil pan mounting bolts.
10. Install drain plug to oil pan.
CAUTION:
Do not reuse drain plug gasket.
11. Install control rod. Refer to
AT-217, "Control Rod Removal and Installation"
12. Install rear propeller shaft. Refer to
PR-5, "Removal and Installation"
.
13. Install exhaust front tube and center muffler. Refer to
EX-3, "Removal and Installation"
.
14. Pour ATF into A/T assembly. Refer to
.
15. Connect the battery cable to the negative terminal.
SCIA5676E
SCIA2308E
: 7.9 N·m (0.81 kg-m, 70 in-lb)
: 34 N·m (3.5 kg-m, 25 ft-lb)
SCIA4113E
AT-248
AIR BREATHER HOSE
AIR BREATHER HOSE
PFP:31098
Removal and Installation
NCS0011C
Refer to the figure below for air breather hose removal and installation procedure.
CAUTION:
●
When installing an air breather hose, be careful not to be crushed or blocked by folding or bend-
ing the hose.
●
When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend “R” portion.
SCIA6953E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст