Infiniti Q45. Manual — part 319
VEHICLE INFORMATION AND INTEGRATED SWITCH SYSTEM /WITHOUT
NAVIGATION SYSTEM
DI-143
C
D
E
F
G
H
I
J
L
M
A
B
DI
2.
CHECK HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect AV control unit connector and display connector.
3.
Check continuity as follows.
●
When the screen looks bluish
●
When the screen looks reddish
●
When the screen looks yellowish
OK or NG
OK
>> GO TO 3.
NG
>>
●
Check connector housings for disconnected or loose terminals.
●
Repair harness or connector.
Terminals
Continuity
AV control unit
Display
Connector
Terminal
Connector
Terminal
M78
18
M82
1
Yes
M78
14
M82
4
Terminals
Continuity
(+)
(–)
Connector
Terminal
M78
14, 18
Ground
No
Terminals
Continuity
AV control unit
Display
Connector
Terminal
Connector
Terminal
M78
21
M82
2
Yes
M78
14
M82
4
Terminals
Continuity
(+)
(–)
Connector
Terminal
M78
14, 21
Ground
No
Terminals
Continuity
AV control unit
Display
Connector
Terminal
Connector
Terminal
M78
24
M82
3
Yes
M78
14
M82
4
Terminals
Continuity
(+)
(–)
Connector
Terminal
M78
14, 24
Ground
No
PKIA9699E
PKIA9700E
PKIA9701E
DI-144
VEHICLE INFORMATION AND INTEGRATED SWITCH SYSTEM /WITHOUT
NAVIGATION SYSTEM
3.
CHECK RGB SIGNAL
1.
Connect AV control unit connector and display connector.
2.
Turn ignition switch ON.
3.
Display “Color bar” by “CONFIRMATION/ADJUSTMENT” mode.
4.
Check the following.
●
When the screen looks bluish
Voltage signal between AV control unit harness connector M78 ter-
minals 18 and 14
●
When the screen looks reddish
Voltage signal between AV control unit harness connector M78 terminals 21 (Y) and 14
●
When the screen looks yellowish
Voltage signal between AV control unit harness connector M78 terminals 24 (G) and 14
OK or NG
OK
>> Replace display.
NG
>> Replace AV control unit.
RGB Screen Is Rolling
NKS001D0
1.
CHECK HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect AV control unit connector and display connector.
3.
Check continuity between AV control unit harness connector
M78 terminal 15 and display harness connector M82 terminal 7.
4.
Check continuity between AV control unit harness connector
M78 terminal 15 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness or connector.
18 – 14:
21 – 14:
24 – 14:
PKIA9702E
SKIA0165E
SKIA0166E
SKIA0167E
15 – 7
: Continuity should exist.
15 – Ground
: Continuity should not exist.
PKIA9703E
VEHICLE INFORMATION AND INTEGRATED SWITCH SYSTEM /WITHOUT
NAVIGATION SYSTEM
DI-145
C
D
E
F
G
H
I
J
L
M
A
B
DI
2.
CHECK RGB SYNCHRONIZING SIGNAL
1.
Connect AV control unit connector and display connector.
2.
Turn ignition switch ON.
3.
Check voltage signal between AV control unit harness connector
M78 terminals 15 and 10.
OK or NG
OK
>> Replace display.
NG
>> Replace AV control unit.
No A/C Display is Shown
NKS001D1
Refer to
ATC-107, "A/C Display is Malfunctioning"
A/C Operation Is Not Possible
NKS001D2
Refer to
ATC-108, "A/C Operation is Malfunctioning"
No Fuel Information Is Displayed/No Warning Message Is Displayed
NKS001D3
1.
CHECK HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect connectors of AV control unit, combination meter
and BCM.
3.
Check continuity between AV control unit harness connector
M77 terminal 34 and combination meter harness connector M41
terminal 7.
4.
Check continuity between AV control unit harness connector
M77 terminal 35 and combination meter harness connector M41
terminal 6.
5.
Check continuity between AV control unit harness connector M77 terminals 34, 35 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness or connector.
15 – 10:
PKIA9704E
SKIA0164E
34 – 7
: Continuity should exist.
35 – 6
: Continuity should exist.
34 – Ground
: Continuity should not exist.
35 – Ground
PKIA9705E
DI-146
VEHICLE INFORMATION AND INTEGRATED SWITCH SYSTEM /WITHOUT
NAVIGATION SYSTEM
2.
CHECK COMMUNICATION SIGNAL (AV-ME)
1.
Connect connectors of combination meter, BCM and AV control
unit.
2.
Turn ignition switch ON and display “VEHICLE ELECTRONIC
SYSTEMS” screen.
3.
Check voltage signal between AV control unit harness connector
M77 terminal 34 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Replace AV control unit.
3.
CHECK COMMUNICATION SIGNAL (MEAV)
1.
Turn ignition switch ON and display “VEHICLE ELECTRONIC
SYSTEMS” screen.
2.
Check voltage signal between AV control unit harness connector
M77 terminal 35 and ground.
OK or NG
OK
>> Replace AV control unit.
NG
>> Replace combination meter.
34 – Ground:
PKIA9706E
SKIA0169E
35 – Ground:
PKIA9707E
SKIA0170E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст