Infiniti Q45. Manual — part 100
ASSEMBLY
AT-313
D
E
F
G
H
I
J
K
L
M
A
B
AT
g.
Install control valve with TCM in transmission case.
CAUTION:
●
Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole.
●
Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
●
Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
●
Assemble it so that manual valve cutout is engaged with
manual plate projection.
h.
Install bolts A, B and C to control valve with TCM.
i.
Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1
→
2
→
3), and then tighten other
bolts.
10. Connect A/T fluid temperature sensor 2 connector.
SCIA5034E
SCIA5035E
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA5025E
SCIA5037E
SCIA5023E
AT-314
ASSEMBLY
11. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
12. Connect revolution sensor connector.
13. Securely fasten revolution sensor 2 harness with terminal clip.
14. Pull down A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
15. Install snap ring to A/T assembly harness connector.
SCIA5446E
SCIA7518E
SCIA7526E
SCIA5299E
SCIA5300E
ASSEMBLY
AT-315
D
E
F
G
H
I
J
K
L
M
A
B
AT
16. Install magnets in oil pan.
17. Install oil pan to transmission case.
a.
Install oil pan gasket to transmission case.
CAUTION:
●
Do not reuse oil pan gasket.
●
Install it in the direction to align hole positions.
●
Completely remove all moisture, oil and old gasket, etc. from oil pan gasket mounting surface.
b.
Install oil pan to transmission case.
CAUTION:
●
Install it so that drain plug comes to the position as
shown in the figure.
●
Be careful not to pinch harnesses.
●
Completely remove all moisture, oil and old gasket, etc.
from oil pan gasket mounting surface.
c.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
CAUTION:
Do not reuse oil pan mounting bolts.
18. Install drain plug to oil pan.
CAUTION:
Do not reuse drain plug gasket.
19. Install torque converter.
a.
Pour ATF into torque converter.
●
Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of ATF is
required for a new torque converter.
●
When reusing old torque converter, add the same amount
of ATF as was drained.
SCIA5200E
SCIA2308E
: 7.9 N·m (0.81 kg-m, 70 in-lb)
: 34 N·m (3.5 kg-m, 25 ft-lb)
SCIA4113E
SAT428DA
AT-316
ASSEMBLY
b.
Install torque converter while aligning notches of torque con-
verter with notches of oil pump.
CAUTION:
Install torque converter while rotating it.
c.
Measure distance “A” to make sure that torque converter is in
proper position.
SCIA5010E
Distance “A”:
22.0 mm (0.87 in) or more
SCIA5694E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст