Infiniti Q45. Manual — part 811
G SENSOR
SCS-61
C
D
F
G
H
I
J
K
L
M
A
B
SCS
G SENSOR
PFP:98805
Removal and Installation
NES000CJ
CAUTION:
Never drop or strike the vertical G sensor, because it has little endurance to impact.
REMOVAL
Front Vertical G Sensor
1.
Remove the lower dash side finisher. Refer to
2.
Remove the SMJ harness connector bolt.
3.
Remove the IVMS control unit. Refer to
4.
Disconnect the front vertical G sensor connector.
5.
Remove the front vertical G sensor bolts.
6.
Remove the front vertical G sensor (1).
Rear Vertical G Sensor
1.
Remove the seat cushion trim and pad (RH). Refer to
SE-191, "Removal and Installation"
.
2.
Remove the seatback trim and pad (RH). Refer to
SE-191, "Removal and Installation"
3.
Remove the rear pillar finisher. Refer to
EI-43, "Removal and Installation"
.
4.
Disconnect the rear vertical G sensor connector.
5.
Remove the rear vertical G sensor bolts.
6.
Remove the rear vertical G sensor (1).
INSTALLATION
Note the following, and installation is the reverse order of removal.
●
When installing each vertical G sensor, tighten bolts to the specified torque.
CAUTION:
Never drop or strike the vertical G sensor, because it has little endurance to impact.
●
After the installation, check each vertical G sensor value on “DATA MONITOR” of CONSULT-II. If it is out-
side the standard, replace each vertical G sensor. Refer to
.
SEIA0728E
SEIA0729E
Vertical G sensor bolts
: 3.4 N·m (0.35 kg-m, 30 in-lb)
SCS-62
G SENSOR
SE-1
SEAT
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
SE
A
B
SE
SEAT
PRECAUTIONS . . . . . . . . . . . . . . .. 4
PREPARATION . . . . . . . . . . . . . . ... 6
Special Service Tools . . . . . . . . . . . ... 6
Commercial Service Tools . . . . . . . . . . 6
SQUEAK AND RATTLE TROUBLE DIAGNOSES . . 7
Work Flow . . . . . . . . . . . . . . . . 7
Generic Squeak and Rattle Troubleshooting . . ... 9
Diagnostic Worksheet . . . . . . . . . . . .11
AUTOMATIC DRIVE POSITIONER . . . . . . .. 13
System Description . . . . . . . . . . . . 13
Component Parts and Harness Connector Location
CONSULT-II Function . . . . . . . . . . . . 39
CONSULT-II BASIC OPERATION PROCEDURE
SE-2
POWER SEAT . . . . . . . . . . . . . . ... 92
WITH HEATED SEAT . . . . . . . . . . 109
WITHOUT HEATED SEAT . . . . . . . . 110
Check Rear Power Seat Sliding Motor Circuit . ...111
WITH HEATED SEAT . . . . . . . . . . .111
WITHOUT HEATED SEAT . . . . . . . . 112
Check Rear Power Seat Switch Circuit . . . . 113
WITH HEATED SEAT . . . . . . . . . . 113
WITHOUT HEATED SEAT . . . . . . . . 114
Check Auto Return Cancel Switch Circuit 1 . . . 116
WITH HEATED SEAT . . . . . . . . . . 116
WITHOUT HEATED SEAT . . . . . . . . 116
Check Auto Return Cancel Switch Circuit 2 . . . 117
WITH HEATED SEAT . . . . . . . . . . 117
WITHOUT HEATED SEAT . . . . . . . . . 118
Check Rear Door Switch Circuit . . . . . . ... 119
WITH HEATED SEAT . . . . . . . . . . 119
WITHOUT HEATED SEAT . . . . . . . . .120
Check Rear Power Seat Sliding Sensor Circuit . 122
WITH HEATED SEAT . . . . . . . . . . 122
WITHOUT HEATED SEAT . . . . . . . . .123
HEATED SEAT . . . . . . . . . . . . . . 124
Component Parts and Harness Connector Location .124
System Description . . . . . . . . . . . ...125
FRONT HEATED SEAT . . . . . . . . . .125
REAR HEATED SEAT . . . . . . . . . ...125
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст