Infiniti Q45. Manual — part 758
REAR DRIVE SHAFT
RAX-13
C
E
F
G
H
I
J
K
L
M
A
B
RAX
8.
Position boot securely into grooves (indicated by * marks)
shown in the figure.
CAUTION:
If there is grease on boot mounting surfaces (indicated by*
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
9.
Make sure the boot installation length “L” is the length indicated
below. Insert a flat-bladed screwdriver or similar tool into the
smaller side of boot. Bleed air from boot to prevent boot defor-
mation.
CAUTION:
●
Boot may break if boot installation length is out of the standard value.
●
Take care not to touch the tip of screwdriver to inside of boot.
10. Secure the big and small ends of boot with new boot bands as
shown in the figure.
NOTE:
Discard old boot bands; replace with new ones.
11. After installing housing and shaft, rotate boot to check whether
or not the actual position is correct. If boot position is not correct,
secure boot with new boot band again.
Wheel Side
1.
Insert the majority of the specified amount grease (NISSAN gen-
uine grease or equivalent) into joint sub-assembly serration hole
until grease begins to ooze from ball groove and serration hole.
After insert grease, use a shop cloth to wipe off old grease that
has oozed out.
2.
Wind serrated part of shaft with tape. Install boot band and boot
to shaft. Be careful not to damage boot.
NOTE:
Discard old boot band and boot; replace with new ones.
3.
Remove protective tape wound around serrated part of shaft.
Boot installation Length “L”
: 93.9 mm (3.697 in)
SDIA2400E
SFA395
SDIA1127E
SFA800
RAX-14
REAR DRIVE SHAFT
4.
Attach circular clip to shaft. At this time, circular clip must fit
securely into shaft groove. Attach nut to joint sub-assembly.
NOTE:
Discard old circular clip; replace with new one.
5.
Insert the remainder of the specified amount grease (NISSAN
genuine grease or equivalent) listed below into housing from the
large end of boot.
6.
Install boot securely into grooves (indicated by * marks) shown
in the figure.
CAUTION:
If there is grease on boot mounting surfaces (indicated by *
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
7.
Make sure the boot installation length “L” is the length indicated
below. Insert a flat-bladed screwdriver or similar tool into the
smaller side of boot. Bleed air from boot to prevent boot defor-
mation.
CAUTION:
●
Boot may brake if boot installation length is out of the standard value.
●
Be careful that screwdriver tip doe not contact inside surface of boot.
8.
Secure the big and small ends of boot with new boot bands as
shown in the figure.
NOTE:
Discard old boot bands; replace with new ones.
9.
After installing joint sub-assembly and shaft, rotate boot to check
whether or not the actual position is correct. If boot position is
not correct, secure boot with new boot bands again.
Grease amount
: 86 - 96 g (3.03 - 3.39 oz)
RAC0049D
Boot installation length “L”
: 97 mm (3.82 in)
SDIA2401E
SFA395
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-15
C
E
F
G
H
I
J
K
L
M
A
B
RAX
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Wheel Bearing
NDS0006S
Drive Shaft
NDS0006T
Axial end play
0.05 mm (0.002 in) or less
Rotating torque
Less than 1.49 N·m (0.15 kg-m, 13 in-lb)
Measurement of spring balance
Less than 12.8 N (1.31 kg, 2.88 lb)
Measuring point (Brake caliper installation points)
SDIA2655E
Joint type
Wheel side
Final drive side
Grease quantity
86 - 96 g (3.03 - 3.39 oz)
124 - 134 g (4.37 - 4.73 oz)
Boot installation length
97 mm (3.82 in)
93.9 mm (3.697 in)
RAX-16
SERVICE DATA AND SPECIFICATIONS (SDS)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст