Infiniti Q45. Manual — part 583
FUEL TANK
FL-9
C
D
E
F
G
H
I
J
K
L
M
A
FL
6.
Remove fuel filler neck cover.
7.
Remove filer tube.
8.
Remove fuel tank mounting band mounting bolts.
9.
If the bottom of fuel tank hard contacts to remove from trunk
floor panel, insert a wood block or something similar to separate
them.
CAUTION:
Use a shop cloth or others like that to avoid deformation or
damage to fuel tank and the floor panel.
10. Pull fuel tank backwards to remove.
INSTALLATION
Note the following, and install in the reverse order of removal.
●
Push mounting band pin to the vehicle side securely.
●
Referring to the mating marks marked during removal, install fuel tubes and EVAP tubes and fix to the
clamps securely.
●
Before fixing fuel tank, temporarily install filler tube.
CAUTION:
Use genuine filler tube mounting bolts or equivalent. Make sure to tighten them to the specified
torque.
●
To connect quick connector, refer to
FL-3, "Removal and Installation"
.
INSPECTION AFTER INSTALLATION
After installing tubes, make sure there is no fuel leakage at connections in the following steps.
●
Apply fuel pressure to fuel lines with turning ignition switch “ON” (with engine stopped). Then check for
fuel leaks at connections.
●
Start engine and rev it up and check for fuel leaks at connections.
PBIC2131E
PBIC0169E
PBIC1196E
FL-10
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Standard and Limit
NBS0028L
Fuel tank capacity
Approx. 80
(21-1/8 US gal, 17-5/8 Imp gal)
Fuel recommendation
Refer to
FSU-1
FRONT SUSPENSION
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION
FSU
A
B
FSU
FRONT SUSPENSION
PRECAUTION . . . . . . . . . . . . . . . 2
Caution . . . . . . . . . . . . . . . . . . 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools (SST) . . . . . . . . . . 3
Commercial Service Tools . . . . . . . . . . 3
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 4
NVH Troubleshooting Chart . . . . . . . . . . 4
FRONT SUSPENSION ASSEMBLY . . . . . . ... 5
On-Vehicle Inspection and Service . . . . . . .. 5
INSPECTION LOWER BALL JOINT END PLAY
STRUT INSPECTION . . . . . . . . . . ... 5
Wheel Alignment Inspection . . . . . . . . . . 5
Components . . . . . . . . . . . . . . . . 7
COIL SPRING AND STRUT . . . . . . . . . ... 8
Removal and Installation . . . . . . . . . . .. 8
REMOVAL . . . . . . . . . . . . . . . . 8
INSTALLATION . . . . . . . . . . . . . . 9
Disassembly and Assembly . . . . . . . . . 10
SUSPENSION ARM . . . . . . . . . . . . .. 13
Removal and Installation . . . . . . . . . . 13
STABILIZER BAR . . . . . . . . . . . . . . 15
Removal and Installation . . . . . . . . . . 15
FRONT SUSPENSION MEMBER . . . . . . . . 16
Removal and Installation . . . . . . . . . . 16
FSU-2
PRECAUTION
PRECAUTION
PFP:00001
Caution
NES00061
●
When installing rubber bushings, the final tightening must be carried out under unladen conditions with
tires on ground. Oil will shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
●
Unladen conditions mean that fuel, engine coolant and lubricant are full. A spare tire, a jack, hand tools
and mats are in designated positions.
●
After servicing suspension parts, be sure to check wheel alignment.
●
Self-lock nuts are not reusable. Always use new ones when installing. Since new caulking nuts are pre-
oiled, tighten as they are.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст