Infiniti Q45. Manual — part 209
DOOR
BL-105
C
D
E
F
G
H
J
K
L
M
A
B
BL
2.
Adjust the striker so that it becomes parallel with the lock inser-
tion direction.
Removal and Installation of Front Door
NIS000V8
CAUTION:
●
When removing and installing the door assembly, support the door with a jack and cloth to protect
the door and body.
●
Operate with two workers, because of its heavy weight.
●
When removing and installing front door assembly, be sure to perform the fitting adjustment Refer
to
●
Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
●
After installing, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
●
After installing, check operation.
REMOVAL
1.
Pull the lever and remove the front door harness connector
while removing tabs of door harness connector.
2.
Remove the check link cover.
3.
Remove the mounting bolts of the check link on the vehicle.
SIIA0338E
PIIA2514E
SIIA0339E
BL-106
DOOR
4.
Remove the door-side hinge mounting bolts and nuts, and
remove the door assembly.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Rear Door
NIS000V9
CAUTION:
●
When removing and installing the rear door assembly, support the door with a jack and cloth to
protect the door and body.
●
Operate with two workers, because of its heavy weight.
●
When removing and installing rear door assembly, be sure to perform the fitting adjustment Refer
to
.
●
Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
●
After installing, apply touch-up paint (the body color) onto the head of the hinge mounting nuts.
●
After installing, check operation.
REMOVAL
1.
Grommet is pulled out, and the Rear door harness connector is
detached.
2.
Remove the check link cover.
3.
Remove the mounting bolts of the check link on the vehicle.
PIIA3473E
PIIA3412E
PIIA2788E
DOOR
BL-107
C
D
E
F
G
H
J
K
L
M
A
B
BL
4.
Remove the door-side hinge mounting nuts, and remove the
door assembly.
INSTALLATION
Install in the reverse order of removal.
Door Weatherstrip
NIS000VA
REMOVAL
1.
Remove the mounting bolts of the check link on the vehicle. Refer to
BL-105, "Removal and Installation of
or
BL-106, "Removal and Installation of Rear Door"
2.
Remove the weatherstrip clips and remove weatherstrip.
CAUTION:
After removal, do not pull strongly on the weatherstrip.
INSTALLATION
Install in the reverse order of removal.
PIIA3431E
SIIA0328E
BL-108
FRONT DOOR LOCK
FRONT DOOR LOCK
PFP:80502
Component Structure
NIS000VB
Inspection and Adjustment
NIS000VC
1.
Remove the front door finisher. Refer to
EI-35, "Removal and Installation"
.
2.
Remove the front speaker. Refer to
AV-53, "Removal and Installation of Door Speaker"
3.
Remove the front door window. Refer to
GW-51, "Removal and Installation"
.
4.
Remove the front door module assembly. Refer to
GW-51, "Removal and Installation"
EXTERIOR HANDLE ROD ADJUSTMENT
Rotate the bushing to adjust so that the clearance between the bush-
ing and rod becomes as shown in the figure.
CAUTION:
Be careful not to make the clearance 0 mm (0 in) or the rod
pressed continuously.
Removal and Installation
NIS000VD
REMOVAL
1.
Remove the front door finisher. Refer to
EI-35, "Removal and Installation"
.
2.
Remove the front speaker. Refer to
AV-53, "Removal and Installation of Door Speaker"
3.
Remove the front door window.
GW-51, "Removal and Installation"
.
4.
Remove the front door module assembly.
GW-51, "Removal and Installation"
1.
Outside handle
2.
Key cylinder (Driver side only)
3.
Outside handle rod
4.
Key lock rod
5.
Door lock assembly
6.
Door lock actuator
7.
Inside handle cable
8.
Inside handle
9.
Lock knob cable
10. Lock knob
PIIA3475E
SBT978
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст