Infiniti Q45. Manual — part 591
HOW TO USE THIS MANUAL
GI-9
C
D
E
F
G
H
I
J
K
L
M
B
GI
Components
NAS0003V
●
THE LARGE ILLUSTRATIONS are exploded views (see the following) and contain tightening torques,
lubrication points, section number of the PARTS CATALOG (e.g. SEC. 440) and other information neces-
sary to perform repairs.
The illustrations should be used in reference to service matters only. When ordering parts, refer to the
appropriate PARTS CATALOG .
Components shown in an illustration may be identified by a circled number. When this style of illustration
is used, the text description of the components will follow the illustration.
SYMBOLS
1.
Union bolt
2.
Copper washer
3.
Brake hose
4.
Cap
5.
Bleed valve
6.
Sliding pin bolt
7.
Piston seal
8.
Piston
9.
Piston boot
10.
Cylinder body
11.
Sliding pin
12.
Torque member mounting bolt
13.
Washer
14.
Sliding pin boot
15.
Bushing
16.
Torque member
17.
Inner shim cover
18.
Inner shim
19.
Inner pad
20.
Pad retainer
21.
Pad wear sensor
22.
Outer pad
23.
Outer shim
24.
Outer shim cover
1: PBC (Poly Butyl Cuprysil) grease
or silicone-based grease
2: Rubber grease
: Brake fluid
Refer to GI section for additional symbol definitions.
SFIA2959E
SAIA0749E
GI-10
HOW TO USE THIS MANUAL
How to Follow Trouble Diagnoses
NAS0003W
DESCRIPTION
NOTICE:
Trouble diagnoses indicate work procedures required to diagnose problems effectively. Observe the following
instructions before diagnosing.
1.
Before performing trouble diagnoses, read the “Preliminary Check”, the “Symptom Chart” or the
“Work Flow”.
2.
After repairs, re-check that the problem has been completely eliminated.
3.
Refer to Component Parts and Harness Connector Location for the Systems described in each
section for identification/location of components and harness connectors.
4.
Refer to the Circuit Diagram for quick pinpoint check.
If you need to check circuit continuity between harness connectors in more detail, such as when a
sub-harness is used, refer to Wiring Diagram in each individual section and Harness Layout in PG
section for identification of harness connectors.
5.
When checking circuit continuity, ignition switch should be OFF.
6.
Before checking voltage at connectors, check battery voltage.
7.
After accomplishing the Diagnostic Procedures and Electrical Components Inspection, make sure
that all harness connectors are reconnected as they were.
HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES
1.
Work and diagnostic procedure
Start to diagnose a problem using procedures indicated in enclosed test groups.
2.
Questions and required results
Questions and required results are indicated in bold type in test group.
The meaning of are as follows:
SAIA0256E
HOW TO USE THIS MANUAL
GI-11
C
D
E
F
G
H
I
J
K
L
M
B
GI
3.
Symbol used in illustration
Symbols included in illustrations refer to measurements or procedures. Before diagnosing a problem,
familiarize yourself with each symbol. Refer to "Connector Symbols" in GI Section and "KEY TO SYM-
BOLS SIGNIFYING MEASUREMENTS OR PROCEDURES" below.
4.
Action items
Next action for each test group is indicated based on result of each question. Test group number is shown
in the left upper portion of each test group.
HARNESS WIRE COLOR AND CONNECTOR NUMBER INDICATION
There are two types of harness wire color and connector number indication.
TYPE 1: Harness Wire Color and Connector Number are Shown in Illustration
●
Letter designations next to test meter probe indicate harness
wire color.
●
Connector numbers in a single circle (e.g. M33) indicate har-
ness connectors.
●
Connector numbers in a double circle (e.g. F211) indicate com-
ponent connectors.
a. Battery voltage
→
11 - 14V or approximately 12V
b. Voltage
: Approximately 0V
→
Less than 1V
AGI070
GI-12
HOW TO USE THIS MANUAL
TYPE 2: Harness Wire Color and Connector Number are Shown in Text
KEY TO SYMBOLS SIGNIFYING MEASUREMENTS OR PROCEDURES
SGI144A
SAIA0750E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст