Infiniti Q45. Manual — part 547
PRECAUTIONS
EM-5
C
D
E
F
G
H
I
J
K
L
M
A
EM
LIQUID GASKET APPLICATION PROCEDURE
1.
Using a scraper, remove the old liquid gasket adhering to the liq-
uid gasket application surface and the mating surface.
●
Remove the liquid gasket completely from the groove of the
liquid gasket application surface, mounting bolts, and bolt
holes.
2.
Wipe the liquid gasket application surface and the mating sur-
face with white gasoline (lighting and heating use) to remove
adhering moisture, grease and foreign materials.
3.
Attach the liquid gasket tube to tube presser [SST: WS39930000
(
—
)].
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-45, "RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS"
.
4.
Apply the liquid gasket without breaks to the specified location
with the specified dimensions.
●
If there is a groove for the liquid gasket application, apply the
liquid gasket to the groove.
●
As for the bolt holes, normally apply the liquid gasket inside
the holes. Occasionally, it should be applied outside the
holes. Make sure to read the text of this manual.
●
Within 5 minutes of liquid gasket application, install the mating
component.
●
If the liquid gasket protrudes, wipe it off immediately.
●
Do not retighten mounting nuts or bolts after the installation.
●
Wait 30 minutes or more after installing, refill the engine oil and engine coolant.
CAUTION:
If there are specific instructions in this manual, observe them.
PBIC0003E
EMA0622D
SEM159F
EM-6
PREPARATION
PREPARATION
PFP:00002
Special Service Tools
NBS001OA
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV10111100
(J-37228)
Seal cutter
Removing steel oil pan and front cover, etc.
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen
sensors
a: 22 mm (0.87 in)
EG15050500
(J-45402)
Compression gauge adapter
Inspection of compression pressure on No. 7
and No. 8 cylinders
KV10116200
(J-26336-A)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2. KV10109230
(
—
)
Adapter
Disassembling and assembling valve
mechanism
Part (1) is a component of KV10116200 (J-
26336-A), but part (2) is not so.
KV101151S0
(J-38972)
Lifter stopper set
1. KV10115110
(J-38972-1)
Camshaft pliers
2. KV10115120
(J-38972-2)
Lifter stopper
Changing adjusting shims
KV10112100
(BT8653-A)
Angle wrench
Tightening bolts for bearing cap, cylinder
head, etc.
S-NT046
S-NT636
ZZA1225D
PBIC1650E
S-NT041
S-NT014
PREPARATION
EM-7
C
D
E
F
G
H
I
J
K
L
M
A
EM
KV10114700
(J-38139)
Main bearing cap remover
Removing crankshaft main bearing cap
KV10107902
(J-38959)
Valve oil seal puller
Removing valve oil seal
KV10115600
(J-38958)
Valve oil seal drift
Installing valve oil seal
Use side A.
a: 20 (0.79) dia. d: 8 (0.31) dia.
b: 13 (0.51) dia. e: 10.7 (0.421) dia.
c: 10.3 (0.406) dia. f: 5 (0.20) dia.
Unit: mm (in)
EM03470000
(J-8037)
Piston ring compressor
Installing piston assembly into cylinder bore
ST16610001
(J-23907)
Pilot bushing puller
Removing crankshaft pilot converter
WS39930000
(
—
)
Tube presser
Pressing the tube of liquid gasket
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA0023D
S-NT011
S-NT603
S-NT044
S-NT045
S-NT052
EM-8
PREPARATION
Commercial Service Tools
NBS001OB
—
(J- 45476)
Ring gear stopper
Removing and installing crankshaft pulley
—
(J-45488)
Quick connector release
Removing fuel tube quick connectors in
engine room
Tool number
(Kent-Moore No.)
Tool name
Description
PBIC1655E
PBIC0198E
(Kent-Moore No.)
Tool name
Description
( — )
Power tool
Loosening bolts and nuts
(
—
)
Spark plug wrench
Removing and installing spark plug
(J-24239-01)
Cylinder head bolt wrench
Loosening and tightening cylinder head bolt,
and used with angle wrench [SST:
KV10112100 (BT8653-A)]
a: 13 (0.51) dia.
b: 12 (0.47)
c: 10 (0.39)
Unit: mm (in)
(
—
)
Valve seat cutter set
Finishing valve seat dimensions
PBIC0190E
S-NT047
NT583
S-NT048
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст