Infiniti Q45. Manual — part 706
STEP LAMP
LT-161
C
D
E
F
G
H
I
J
L
M
A
B
LT
Switch Monitor Cancellation
If the following conditions are satisfied, the communication diagnosis is cancelled.
●
Turn ignition switch OFF.
●
Drive the vehicle more than 7 km/h (4 MPH).
Symptom Chart
NKS001AI
DIAGNOSTIC PROCEDURE
SYMPTOM: Step Lamp Does Not Illuminate/Dose Not Go Off When Door Is Opened/Closed
1.
CHECK DOOR SWITCH SIGNAL
With CONSULT-II
●
Operate each door via “DOOR SW” on DATA MONITOR screen
and make sure that switch turns on and off as commanded.
Without CONSULT-II
●
Operate each door and via “switch monitor” of self-diagnosis function and make sure that switch turns on
and off as commanded.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
SKIA0441E
LT-162
STEP LAMP
2.
CHECK DOOR SWITCH HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect each door switch connector and BCM connector.
3.
Check continuity between each door switch harness connector
and BCM harness connector.
OK or NG
OK
>>
●
Check door switch ground condition.
●
Replace door switch.
NG
>> Repair harness or connector.
3.
CHECK BULB
Check step lamp bulb.
OK or NG
OK
>> GO TO 4.
NG
>> Replace bulb.
4.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect step lamp connector.
3.
Check voltage between step lamp connector D10, D40, D60,
D80 terminal 1 and ground.
OK or NG
OK
>> Check harness for open or short between step lamp and
door control unit.
NG
>> Check the following.
●
10A fuse [No. 8, located in fuse block (J/B) No. 1]
●
Harness for open or short between fuse and step lamp
PKIB1690E
Terminal
Continuity
BCM
connector
Terminal Door
switch
connector
Terminal
B4
142
B20
Front door switch
(driver side)
1
Yes
143 D82
Door lock assembly
rear RH (door switch)
1
M4
33
D62
Door lock assembly
rear LH (door switch)
1
37
B220
Front door switch
(passenger side)
1
PKIB1691E
1 - Ground
: Battery voltage
PKIA5166E
STEP LAMP
LT-163
C
D
E
F
G
H
I
J
L
M
A
B
LT
Bulb Replacement
NKS001AJ
1.
Remove step lamp. Refer to
LT-163, "Removal and Installation"
2.
Insert a screwdriver in the notch and remove lens.
3.
Remove bulb.
Removal and Installation
NKS001AK
1.
Using a clip driver or a suitable tool, press and remove metal clip
of step lamp.
2.
Disconnect step lamp connector.
Step lamp
: 12V - 2.7W
PKIA0075E
PKIA0076E
LT-164
DOOR MIRROR LAMP
DOOR MIRROR LAMP
PFP:96301
System Description
NKS001AL
The door mirror foot well lamp for approx. 15 seconds when door unlocking operation is commanded with
remote controller.
It goes off when the driver door is opened during illumination after the door unlocking operation with remote
controller.
Power is supplied at all times
●
to each door mirror [door mirror (foot well) lamp] terminal 4
●
through 10A fuse [No. 8, located in fuse block (J/B) No.1].
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст